European network of stockholding machinery dealers

Category:
    Manufacturer:
      Machines:
        Trader:

          Karl Günter Wirths GmbH - Stockist for used machines

          Machinelist:


          Center Lathe

          used  Center Lathe PBR T-600 LC


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-2000127 · Center Lathe

          PBR - T-600 LC - - 1994 -

          Technical details
          turning diameter over bed 1230 mm︱turning diameter over slide 890 mm︱turning length 3000 mm︱spindle passage 150 mm︱turning speeds 4-800 U/min︱main drive motor 30 HP/PS︱feed - longitudinal/cross 0,05- 22,4 mm/rev (U)︱rapid travel - longitudinal/face 2,5 m/min︱rapid return speed 5 m/min︱max. workpiece weight between centres 5000 kg︱bed width 670 mm︱face slide travel 640 mm︱weight of the machine ca. 9,2 t︱dimensions of the machine ca. 5,5 x 1,75 x 1,6 m︱
          Machine has a moving steady and a fixed steady. It has some accessories, Multifix holder, 3 jaw chuck and DRO.
            turning diameter over bed 1230 mm
            turning diameter over slide 890 mm
            turning length 3000 mm
            spindle passage 150 mm
            turning speeds 4-800 U/min
            main drive motor 30 HP/PS
            feed - longitudinal/cross 0,05- 22,4 mm/rev (U)
            rapid travel - longitudinal/face 2,5 m/min
            rapid return speed 5 m/min
            max. workpiece weight between ce. 5000 kg
            bed width 670 mm
            face slide travel 640 mm
            weight of the machine ca. 9,2 t
            dimensions of the machine ca. 5,5 x 1,75 x 1,6 m
            Description :
            Machine has a moving steady and a fixed steady. It has some accessories,
            Multifix holder, 3 jaw chuck and DRO.
          Datasheet
          Request / Contact
          used  Center Lathe NARDINI MS 175 E


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-2000129 · Center Lathe

          NARDINI - MS 175 E - - 1990 -

          Technical details
          turning diameter over bed 0350 mm︱turning diameter over slide rest 205 mm︱turning length 800 mm︱spindle turning speed range 50 - 2000 U/min︱spindle bore 40 mm︱feeds: bed slide/longitudinal 0,042 - 0,929 mm/U︱feeds - cross 0,015 - 0,338 mm/U︱total power requirement 4,1 kW︱weight of the machine ca. 1,2 t︱dimensions of the machine ca. 1,8 x 0,8 x 1,5 m︱
            turning diameter over bed 0350 mm
            turning diameter over slide rest 205 mm
            turning length 800 mm
            spindle turning speed range 50 - 2000 U/min
            spindle bore 40 mm
            feeds: bed slide/longitudinal 0,042 - 0,929 mm/U
            feeds - cross 0,015 - 0,338 mm/U
            total power requirement 4,1 kW
            weight of the machine ca. 1,2 t
            dimensions of the machine ca. 1,8 x 0,8 x 1,5 m
          Datasheet
          Request / Contact
          used  Center Lathe MONDIALE Celtic 12


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-2000132 · Center Lathe

          MONDIALE - Celtic 12 - - 1984 -

          Technical details
          turning diameter over bed 0305 mm︱turning diameter over slide rest 170 mm︱turning length 800 mm︱spindle turning speed range 40- 2000 U/min︱voltage 400 V︱feed per revolution mm︱rapid travel - longitudinal/face m/min︱spindle bore 28 mm︱total power requirement 2 kW︱weight of the machine ca. 625 kg︱dimensions of the machine ca. 1,65 x 0,6 x 1,4 m︱
          Accessories: Multifix with 1 holder, machine light, three jaw chuck.
            turning diameter over bed 0305 mm
            turning diameter over slide rest 170 mm
            turning length 800 mm
            spindle turning speed range 40- 2000 U/min
            voltage 400 V
            spindle bore 28 mm
            total power requirement 2 kW
            weight of the machine ca. 625 kg
            dimensions of the machine ca. 1,65 x 0,6 x 1,4 m
            Description :
            Accessories: Multifix with 1 holder, machine light, three jaw chuck.
          Datasheet
          Request / Contact
          used  Center Lathe MONDIALE Celtic 14


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-2000120 · Center Lathe

          MONDIALE - Celtic 14 - - 1981 -

          Technical details
          turning diameter over bed 0370 mm︱turning diameter over slide rest 240 mm︱turning length 1500 mm︱spindle turning speed range 36- 1600 U/min︱voltage 400 V︱feed per revolution mm︱rapid travel - longitudinal/face m/min︱spindle bore 35 mm︱total power requirement 3 kW︱weight of the machine ca. 1500 kg︱dimensions of the machine ca. 3 x 1,1 x 1,5 m︱
            turning diameter over bed 0370 mm
            turning diameter over slide rest 240 mm
            turning length 1500 mm
            spindle turning speed range 36- 1600 U/min
            voltage 400 V
            spindle bore 35 mm
            total power requirement 3 kW
            weight of the machine ca. 1500 kg
            dimensions of the machine ca. 3 x 1,1 x 1,5 m
            Description :

          Datasheet
          Request / Contact
          used  Center Lathe VDF-BOEHRINGER E 560/1500


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-2000131 · Center Lathe

          VDF-BOEHRINGER - E 560/1500 - - 1970 -

          Technical details
          turning diameter over bed 0610 mm︱turning diameter over slide rest 330 mm︱turning length 1500 mm︱centre height 290 mm︱centre distance 1500 mm︱spindle bore 82 mm︱speeds 9 - 1800 U/min︱feeds longitudinal slide 0,05 - 2,8 mm/U︱feeds cross slide 0,025 - 1,4 mm/U︱weight of the machine ca. 5,0 t︱dimensions of the machine ca. 4,4 x 1,4 x 1,8 m︱voltage 380 V︱
          Accessories: chuck, 4 position tool holder, live center.
            turning diameter over bed 0610 mm
            turning diameter over slide rest 330 mm
            turning length 1500 mm
            centre height 290 mm
            centre distance 1500 mm
            spindle bore 82 mm
            speeds 9 - 1800 U/min
            feeds longitudinal slide 0,05 - 2,8 mm/U
            feeds cross slide 0,025 - 1,4 mm/U
            weight of the machine ca. 5,0 t
            dimensions of the machine ca. 4,4 x 1,4 x 1,8 m
            voltage 380 V
            Description :
            Accessories: chuck, 4 position tool holder, live center.
          Datasheet
          Request / Contact
          used  Center Lathe EXCELLO DLZ 630


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-2000135 · Center Lathe

          EXCELLO - DLZ 630 - - 1965 -

          Technical details
          turning diameter over bed 660 mm︱turning diameter over slide rest 400 mm︱turning length 1500 mm︱centre height 330 mm︱spindle bore 81 mm︱speeds 18 - 1120 U/min︱feeds longitudinal slide 0,05 - 1,4 mm/U︱feeds cross slide 0,016 - 0,46 mm/U︱weight of the machine ca. 4 t︱dimensions of the machine ca. 3 x 1,6 x 1,5 m︱voltage 380 V︱
          Accessories: quick tool changer Multifix with holder, 3 jaw chuck.
            turning diameter over bed 660 mm
            turning diameter over slide rest 400 mm
            turning length 1500 mm
            centre height 330 mm
            spindle bore 81 mm
            speeds 18 - 1120 U/min
            feeds longitudinal slide 0,05 - 1,4 mm/U
            feeds cross slide 0,016 - 0,46 mm/U
            weight of the machine ca. 4 t
            dimensions of the machine ca. 3 x 1,6 x 1,5 m
            voltage 380 V
            Description :
            Accessories: quick tool changer Multifix with holder, 3 jaw chuck.
          Datasheet
          Request / Contact

          CNC Lathe

          used  CNC Lathe GMW HL 1070 x 2000 (3000- 7000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203411 · CNC Lathe

          GMW - HL 1070 x 2000 (3000- 7000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1070 mm︱turning length 2300 (3300- 7300) mm︱control Siemens 828 D ︱turning diameter over slide rest 680 mm︱spindle turning speed range 1 - 800 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 356) mm︱rapid travel - longitudinal/face 10/8 m/min︱switching steps 4 ︱face slide travel 580 mm︱max. workpiece weight between centres 8000 (++) kg︱bed width 665 mm︱total power requirement 22/26 kW︱weight of the machine ca. 12,3 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m. Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1070 mm
            turning length 2300 (3300- 7300) mm
            control Siemens 828 D
            turning diameter over slide rest 680 mm
            spindle turning speed range 1 - 800 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 356) mm
            rapid travel - longitudinal/face 10/8 m/min
            switching steps 4
            face slide travel 580 mm
            max. workpiece weight between ce. 8000 (++) kg
            bed width 665 mm
            total power requirement 22/26 kW
            weight of the machine ca. 12,3 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m.
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1900 x 2000 (3000- 15000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203417 · CNC Lathe

          GMW - HL 1900 x 2000 (3000- 15000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1900 mm︱turning length 2000 (3000- 15000) mm︱control Siemens 828 D ︱turning diameter over slide rest 1400 mm︱spindle turning speed range 1- 400 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 532) mm︱rapid travel - longitudinal/face 6 m/min︱switching steps 4 ︱face slide travel 1050 mm︱max. workpiece weight between centres 15000 kg︱bed width 1120 mm︱total power requirement 37/45 kW︱weight of the machine ca. 20 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m (2- 15 m). Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1900 mm
            turning length 2000 (3000- 15000) mm
            control Siemens 828 D
            turning diameter over slide rest 1400 mm
            spindle turning speed range 1- 400 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 532) mm
            rapid travel - longitudinal/face 6 m/min
            switching steps 4
            face slide travel 1050 mm
            max. workpiece weight between ce. 15000 kg
            bed width 1120 mm
            total power requirement 37/45 kW
            weight of the machine ca. 20 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m (2- 15 m).
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1170 x 2000 (3000- 7000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203410 · CNC Lathe

          GMW - HL 1170 x 2000 (3000- 7000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1170 mm︱turning length 2300 (3300- 7300) mm︱control Siemens 828 D ︱turning diameter over slide rest 780 mm︱spindle turning speed range 1 - 680 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 356) mm︱rapid travel - longitudinal/face 10/8 m/min︱switching steps 4 ︱face slide travel 680 mm︱max. workpiece weight between centres 8000 kg︱bed width 665 mm︱total power requirement 22/26 kW︱weight of the machine ca. 13,3 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m. Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1170 mm
            turning length 2300 (3300- 7300) mm
            control Siemens 828 D
            turning diameter over slide rest 780 mm
            spindle turning speed range 1 - 680 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 356) mm
            rapid travel - longitudinal/face 10/8 m/min
            switching steps 4
            face slide travel 680 mm
            max. workpiece weight between ce. 8000 kg
            bed width 665 mm
            total power requirement 22/26 kW
            weight of the machine ca. 13,3 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m.
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1270 x 2000 (3000- 7000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203412 · CNC Lathe

          GMW - HL 1270 x 2000 (3000- 7000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1270 mm︱turning length 2300 (3300- 7300) mm︱control Siemens 828 D ︱turning diameter over slide rest 880 mm︱spindle turning speed range 1 - 680 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 356) mm︱rapid travel - longitudinal/face 10/8 m/min︱switching steps 4 ︱face slide travel 780 mm︱max. workpiece weight between centres 8000 kg︱bed width 665 mm︱total power requirement 22/26 kW︱weight of the machine ca. 14,3 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m. Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1270 mm
            turning length 2300 (3300- 7300) mm
            control Siemens 828 D
            turning diameter over slide rest 880 mm
            spindle turning speed range 1 - 680 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 356) mm
            rapid travel - longitudinal/face 10/8 m/min
            switching steps 4
            face slide travel 780 mm
            max. workpiece weight between ce. 8000 kg
            bed width 665 mm
            total power requirement 22/26 kW
            weight of the machine ca. 14,3 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m.
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1800 x 2000 (3000- 15000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203415 · CNC Lathe

          GMW - HL 1800 x 2000 (3000- 15000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1800 mm︱turning length 2000 (3000- 15000) mm︱control Siemens 828 D ︱turning diameter over slide rest 1300 mm︱spindle turning speed range 1- 400 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 532) mm︱rapid travel - longitudinal/face 6 m/min︱switching steps 4 ︱face slide travel 1050 mm︱max. workpiece weight between centres 15000 kg︱bed width 1120 mm︱total power requirement 37/45 kW︱weight of the machine ca. 20 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m (2- 15 m). Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1800 mm
            turning length 2000 (3000- 15000) mm
            control Siemens 828 D
            turning diameter over slide rest 1300 mm
            spindle turning speed range 1- 400 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 532) mm
            rapid travel - longitudinal/face 6 m/min
            switching steps 4
            face slide travel 1050 mm
            max. workpiece weight between ce. 15000 kg
            bed width 1120 mm
            total power requirement 37/45 kW
            weight of the machine ca. 20 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m (2- 15 m).
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1620 x 2000 (3000- 8000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203416 · CNC Lathe

          GMW - HL 1620 x 2000 (3000- 8000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1620 mm︱turning length 2300 (3300- 8300) mm︱control Siemens 828 D ︱turning diameter over slide rest 1200 mm︱spindle turning speed range 1- 500 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 532) mm︱rapid travel - longitudinal/face 6 m/min︱switching steps 4 ︱face slide travel 900 mm︱max. workpiece weight between centres 12000 kg︱bed width 850 mm︱total power requirement 30/37 kW︱weight of the machine ca. 16 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m (2- 8 m). Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1620 mm
            turning length 2300 (3300- 8300) mm
            control Siemens 828 D
            turning diameter over slide rest 1200 mm
            spindle turning speed range 1- 500 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 532) mm
            rapid travel - longitudinal/face 6 m/min
            switching steps 4
            face slide travel 900 mm
            max. workpiece weight between ce. 12000 kg
            bed width 850 mm
            total power requirement 30/37 kW
            weight of the machine ca. 16 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m (2- 8 m).
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 2000 x 2000 (3000- 15000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203418 · CNC Lathe

          GMW - HL 2000 x 2000 (3000- 15000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 2000 mm︱turning length 2000 (3000- 15000) mm︱control Siemens 828 D ︱turning diameter over slide rest 1500 mm︱spindle turning speed range 1- 400 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 532) mm︱rapid travel - longitudinal/face 6 m/min︱switching steps 4 ︱face slide travel 1050 mm︱max. workpiece weight between centres 15000 kg︱bed width 1120 mm︱total power requirement 37/45 kW︱weight of the machine ca. 20 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m (2- 15 m). Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 2000 mm
            turning length 2000 (3000- 15000) mm
            control Siemens 828 D
            turning diameter over slide rest 1500 mm
            spindle turning speed range 1- 400 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 532) mm
            rapid travel - longitudinal/face 6 m/min
            switching steps 4
            face slide travel 1050 mm
            max. workpiece weight between ce. 15000 kg
            bed width 1120 mm
            total power requirement 37/45 kW
            weight of the machine ca. 20 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m (2- 15 m).
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1520 x 2000 (3000- 8000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203414 · CNC Lathe

          GMW - HL 1520 x 2000 (3000- 8000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1520 mm︱turning length 2300 (3300- 8300) mm︱control Siemens 828 D ︱turning diameter over slide rest 1100 mm︱spindle turning speed range 1- 500 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 532) mm︱rapid travel - longitudinal/face 6 m/min︱switching steps 4 ︱face slide travel 900 mm︱max. workpiece weight between centres 12000 kg︱bed width 850 mm︱total power requirement 30/37 kW︱weight of the machine ca. 16 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m (2- 8 m). Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1520 mm
            turning length 2300 (3300- 8300) mm
            control Siemens 828 D
            turning diameter over slide rest 1100 mm
            spindle turning speed range 1- 500 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 532) mm
            rapid travel - longitudinal/face 6 m/min
            switching steps 4
            face slide travel 900 mm
            max. workpiece weight between ce. 12000 kg
            bed width 850 mm
            total power requirement 30/37 kW
            weight of the machine ca. 16 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m (2- 8 m).
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GMW HL 1420 x 2000 (3000- 8000)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203413 · CNC Lathe

          GMW - HL 1420 x 2000 (3000- 8000) - - 2021 - Siemens 828 D

          Technical details
          turning diameter 1420 mm︱turning length 2300 (3300- 8300) mm︱control Siemens 828 D ︱turning diameter over slide rest 1000 mm︱spindle turning speed range 1- 500 U/min︱longitudinal feeds: 0,001-500 mm/rev︱cross feeds: 0,001-500 mm/rev︱spindle passage 153 (230- 532) mm︱rapid travel - longitudinal/face 6 m/min︱switching steps 4 ︱face slide travel 900 mm︱max. workpiece weight between centres 12000 kg︱bed width 850 mm︱total power requirement 30/37 kW︱weight of the machine ca. 16 t︱dimensions of the machine ca. 6,9 x 2,7 x 2,6 m︱
          NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered only with a single tool post (Multifix). It could be delivered also with a 12 position Sauter turret. Machine could be ordered in different length, available in steps of 1 m (2- 8 m). Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck, steady, cooling arrangement, hydraulic tailstock,machine LED light and on request with 2 electronic hand wheels for X and Z axes. Control Siemens 828 Dl with shop turn.
            turning diameter 1420 mm
            turning length 2300 (3300- 8300) mm
            control Siemens 828 D
            turning diameter over slide rest 1000 mm
            spindle turning speed range 1- 500 U/min
            longitudinal feeds: 0,001-500 mm/rev
            cross feeds: 0,001-500 mm/rev
            spindle passage 153 (230- 532) mm
            rapid travel - longitudinal/face 6 m/min
            switching steps 4
            face slide travel 900 mm
            max. workpiece weight between ce. 12000 kg
            bed width 850 mm
            total power requirement 30/37 kW
            weight of the machine ca. 16 t
            dimensions of the machine ca. 6,9 x 2,7 x 2,6 m
            Description :
            NEW MACHINE as a flat bed machine ! Machine shown on the photos was ordered
            only with a single tool post (Multifix). It could be delivered also with a 12
            position Sauter turret. Machine could be ordered in different length, available
            in steps of 1 m (2- 8 m).
            Accessories: Machine with housing (CE conform), chip conveyor, three jaw chuck,
            steady, cooling arrangement, hydraulic tailstock,machine LED light and on
            request with 2 electronic hand wheels for X and Z axes.
            Control Siemens 828 Dl with shop turn.
          Datasheet
          Request / Contact
          used  CNC Lathe GILDEMEISTER CTX 410


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203424 · CNC Lathe

          GILDEMEISTER - CTX 410 - - 2006 - Heidenhain 4290

          Technical details
          turning diameter 0410 mm︱turning length 500 mm︱control Heidenhain 4290 ︱turret head 12 pos. VDI 30 ︱swing over bed 520 mm︱spindle turning speed - stepless 25 - 5000 rpm︱spindle bore 79 mm︱feed - longitudinal/cross 0- 24000/20000 mm/min︱rapid travel - longitudinal/face 24/20 m/min︱dimensions 5000 x 1800 x 1800 mm︱total power requirement 44 KVA︱weight of the machine ca. 5,0 t︱
          Machine is with C- axe and life tooling! Control: Heidenhain 4290. Machine has chip conveyor, chuck and tailstock.
            turning diameter 0410 mm
            turning length 500 mm
            control Heidenhain 4290
            turret head 12 pos. VDI 30
            swing over bed 520 mm
            spindle turning speed - stepless 25 - 5000 rpm
            spindle bore 79 mm
            feed - longitudinal/cross 0- 24000/20000 mm/min
            rapid travel - longitudinal/face 24/20 m/min
            dimensions 5000 x 1800 x 1800 mm
            total power requirement 44 KVA
            weight of the machine ca. 5,0 t
            Description :
            Machine is with C- axe and life tooling!
            Control: Heidenhain 4290.
            Machine has chip conveyor, chuck and tailstock.
          Datasheet
          Request / Contact

          Lathe - cycle-controlled

          used  Lathe -  cycle-controlled GORNATI CMG 750 NSXP


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-203402 · Lathe - cycle-controlled

          GORNATI - CMG 750 NSXP - - 1999 - Fagor 8055 T

          Technical details
          turning diameter 1500 mm︱turning length 1500 mm︱control Fagor 8055 T ︱turning diameter over bed slide 1250 mm︱total power requirement 45 kW︱weight of the machine ca. 12 t︱dimensions of the machine ca. 4 x 2,4 x 2,4 m︱
          Zubehör: Vierbackenfutter mit Backen, manuell betätigt, 7 Multifix Halter und ein Halter auf Capto.
            turning diameter 1500 mm
            turning length 1500 mm
            control Fagor 8055 T
            turning diameter over bed slide 1250 mm
            total power requirement 45 kW
            weight of the machine ca. 12 t
            dimensions of the machine ca. 4 x 2,4 x 2,4 m
            Description :
            Zubehör: Vierbackenfutter mit Backen, manuell betätigt, 7 Multifix Halter und
            ein Halter auf Capto.
          Datasheet
          Request / Contact

          Vertical Turret Lathe - Single Column

          used  Vertical Turret Lathe - Single Column GMW RAL-12 (M)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-40096 · Vertical Turret Lathe - Single Column

          GMW - RAL-12 (M) - - 2021 - Fanuc 0i-D

          Technical details
          faceplate diameter 1250 mm︱swing diameter 1600 mm︱turning height 1250 mm︱control Fanuc 0i-D ︱stroke of vertical slide 900 mm︱tool holder 1 ︱distance face plate/tool carrier 700- 1500 mm︱vertical adjustment of the crossrail 800 mm︱workpiece weight 6 t︱faceplate turning speed range -stepless- 1 - 300 U/min︱feeds 0-10000/12000 mm/min︱rapid traverse 10/12 m/min︱horizontal adjustment of slide -200 - +950 mm︱adjustment speed of cross-rail 300 mm/min︱milling spindle - taper SK 50 ︱milling head speed 24 - 2400 U/min︱max. torque on the faceplate 10655 Nm︱total power requirement 50 KVA︱weight of the machine ca. 20,5 t︱
          This machine is a new machine with (M) or without milling spindle. It will be sold with full service and warranty by Wirths GmbH. Control: Fanuc 0i-D. Machine has safety guard and 12/18 (M) position ATC.
            faceplate diameter 1250 mm
            swing diameter 1600 mm
            turning height 1250 mm
            control Fanuc 0i-D
            stroke of vertical slide 900 mm
            tool holder 1
            distance face plate/tool carrier 700- 1500 mm
            vertical adjustment of the cross. 800 mm
            workpiece weight 6 t
            faceplate turning speed range -s. 1 - 300 U/min
            feeds 0-10000/12000 mm/min
            rapid traverse 10/12 m/min
            horizontal adjustment of slide -200 - +950 mm
            adjustment speed of cross-rail 300 mm/min
            milling spindle - taper SK 50
            milling head speed 24 - 2400 U/min
            max. torque on the faceplate 10655 Nm
            total power requirement 50 KVA
            weight of the machine ca. 20,5 t
            Description :
            This machine is a new machine with (M) or without milling spindle. It will be
            sold with full service and warranty by Wirths GmbH.
            Control: Fanuc 0i-D. Machine has safety guard and 12/18 (M) position ATC.
          Datasheet
          Request / Contact
          used  Vertical Turret Lathe - Single Column GMW RAL-16 (M)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-40097 · Vertical Turret Lathe - Single Column

          GMW - RAL-16 (M) - - 2021 - Fanuc 0i-D

          Technical details
          faceplate diameter 1600 mm︱swing diameter 2000 mm︱turning height 1600 mm︱control Fanuc 0i-D ︱stroke of vertical slide 1000 mm︱tool holder 1 ︱distance face plate/tool carrier 1065- 1865 mm︱vertical adjustment of the crossrail 800 mm︱workpiece weight 10 t︱faceplate turning speed range -stepless- 1 - 250 U/min︱feeds 0-10000/12000 mm/min︱rapid traverse 10/12 m/min︱horizontal adjustment of slide -200 - +1125 mm︱adjustment speed of cross-rail 300 mm/min︱milling spindle - taper SK 50 KVA︱milling head speed 50- 2250 U/min︱max. torque on the faceplate 18790 Nm︱total power requirement 60 kW︱weight of the machine ca. 28,5 t︱
          This machine is a new machine with (M) or without milling spindle. It will be sold with full service and warranty by Wirths GmbH. Control: Fanuc 0i-D. Machine has safety guard and 12/18 (M) position ATC.
            faceplate diameter 1600 mm
            swing diameter 2000 mm
            turning height 1600 mm
            control Fanuc 0i-D
            stroke of vertical slide 1000 mm
            tool holder 1
            distance face plate/tool carrier 1065- 1865 mm
            vertical adjustment of the cross. 800 mm
            workpiece weight 10 t
            faceplate turning speed range -s. 1 - 250 U/min
            feeds 0-10000/12000 mm/min
            rapid traverse 10/12 m/min
            horizontal adjustment of slide -200 - +1125 mm
            adjustment speed of cross-rail 300 mm/min
            milling spindle - taper SK 50 KVA
            milling head speed 50- 2250 U/min
            max. torque on the faceplate 18790 Nm
            total power requirement 60 kW
            weight of the machine ca. 28,5 t
            Description :
            This machine is a new machine with (M) or without milling spindle. It will be
            sold with full service and warranty by Wirths GmbH.
            Control: Fanuc 0i-D. Machine has safety guard and 12/18 (M) position ATC.
          Datasheet
          Request / Contact
          used  Vertical Turret Lathe - Single Column GMW RAL-20 (M)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-40098 · Vertical Turret Lathe - Single Column

          GMW - RAL-20 (M) - - 2021 - Fanuc 0i-D

          Technical details
          faceplate diameter 2000 mm︱swing diameter 2500 mm︱turning height 1600 mm︱control Fanuc 0i-D ︱stroke of vertical slide 1000 mm︱tool holder 1 ︱distance face plate/tool carrier 1075 - 1875 mm︱vertical adjustment of the crossrail 800 mm︱workpiece weight 13 t︱faceplate turning speed range -stepless- 1 - 200 U/min︱feeds 0-10000/12000 mm/min︱rapid traverse 10/12 m/min︱horizontal adjustment of slide -250 - +1380 mm︱adjustment speed of cross-rail 300 mm/min︱milling spindle - taper SK 50 ︱milling head speed 50- 2250 U/min︱max. torque on the faceplate 23270 Nm︱total power requirement 60 KVA︱weight of the machine ca. 42 t︱
          This machine is a new machine with (M) or without milling spindle. It will be sold with full service and warranty by Wirths GmbH. Control: Fanuc 0i-D. Machine has safety guard and 12/18 (M) position ATC.
            faceplate diameter 2000 mm
            swing diameter 2500 mm
            turning height 1600 mm
            control Fanuc 0i-D
            stroke of vertical slide 1000 mm
            tool holder 1
            distance face plate/tool carrier 1075 - 1875 mm
            vertical adjustment of the cross. 800 mm
            workpiece weight 13 t
            faceplate turning speed range -s. 1 - 200 U/min
            feeds 0-10000/12000 mm/min
            rapid traverse 10/12 m/min
            horizontal adjustment of slide -250 - +1380 mm
            adjustment speed of cross-rail 300 mm/min
            milling spindle - taper SK 50
            milling head speed 50- 2250 U/min
            max. torque on the faceplate 23270 Nm
            total power requirement 60 KVA
            weight of the machine ca. 42 t
            Description :
            This machine is a new machine with (M) or without milling spindle. It will be
            sold with full service and warranty by Wirths GmbH.
            Control: Fanuc 0i-D. Machine has safety guard and 12/18 (M) position ATC.
          Datasheet
          Request / Contact

          Machining Center - Universal

          used  Machining Center - Universal DECKEL-MAHO DMU 60 T


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-10163 · Machining Center - Universal

          DECKEL-MAHO - DMU 60 T - - 2000 -

          Technical details
          x-travel 0630 mm︱y-travel 560 mm︱z-travel 560 mm︱turning speeds 12.000 U/min︱feed speeds 20-10.000 mm/min︱ 26/26/20 m/min︱ 24-fach ︱spindle taper SK 40 ︱table surface area 1000x600 mm︱total power requirement 26 kW︱weight of the machine ca. 6.500 t︱dimensions of the machine ca. m︱
          Accessories: B-axe (Rotation of head), 24 Pos. ATC with 2 discs, electronic hand wheel, chip conveying worm and cooling arrangement. Machine has cooling through spindle. Control: Heidenhain 430
            x-travel 0630 mm
            y-travel 560 mm
            z-travel 560 mm
            turning speeds 12.000 U/min
            feed speeds 20-10.000 mm/min
            26/26/20 m/min
            24-fach
            spindle taper SK 40
            table surface area 1000x600 mm
            total power requirement 26 kW
            weight of the machine ca. 6.500 t
            Description :
            Accessories: B-axe (Rotation of head), 24 Pos. ATC with 2 discs, electronic
            hand wheel, chip conveying worm and cooling arrangement. Machine has cooling
            through spindle. Control: Heidenhain 430
          Datasheet
          Request / Contact

          Rapid Radial Drilling Machine

          used  Rapid Radial Drilling Machine DONAU DR 23


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-60098 · Rapid Radial Drilling Machine

          DONAU - DR 23 - - 1974 -

          Technical details
          bore capacity in steel (diameter) 23 mm︱arm length 650 mm︱table surface area 1200x800 mm︱swivable table: 700x240 mm︱feed - independent 0,075-0,3 mm︱turning speeds 70-1550 U/min︱total power requirement kW︱weight of the machine ca. 2 t︱dimensions of the machine ca. 2 x 1,6 x 1,9 m︱
            bore capacity in steel (diameter. 23 mm
            arm length 650 mm
            table surface area 1200x800 mm
            swivable table: 700x240 mm
            feed - independent 0,075-0,3 mm
            turning speeds 70-1550 U/min
            weight of the machine ca. 2 t
            dimensions of the machine ca. 2 x 1,6 x 1,9 m
          Datasheet
          Request / Contact

          Bed Type Milling Machine - Universal

          used  Bed Type Milling Machine - Universal FIL FS 130 (CNC)


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-11370 · Bed Type Milling Machine - Universal

          FIL - FS 130 (CNC) - - 1995 -

          Technical details
          longitudinal travel 1300 mm︱vertical movement 1000 mm︱cross travel 1000 mm︱table-size 1600 x 570 mm︱max. table load 2 t︱spindle taper ISO 50 ︱spindle drive 12 kW︱speeds 50 - 2000 U/min︱feeds 5- 10000 mm/min︱rapid traverse 10 m/min︱voltage 400 V︱total power requirement 15 kW︱weight of the machine ca. 9 t︱dimensions of the machine ca. 3,1 x 3,4 x 2,9 m︱
          Bed type milling machine with universal milling head. Machine has a Heidenhain TNC 426 control.
            longitudinal travel 1300 mm
            vertical movement 1000 mm
            cross travel 1000 mm
            table-size 1600 x 570 mm
            max. table load 2 t
            spindle taper ISO 50
            spindle drive 12 kW
            speeds 50 - 2000 U/min
            feeds 5- 10000 mm/min
            rapid traverse 10 m/min
            voltage 400 V
            total power requirement 15 kW
            weight of the machine ca. 9 t
            dimensions of the machine ca. 3,1 x 3,4 x 2,9 m
            Description :
            Bed type milling machine with universal milling head.
            Machine has a Heidenhain TNC 426 control.
          Datasheet
          Request / Contact
          used  Bed Type Milling Machine - Universal WEILER FHP 750


          • Karl Günter Wirths GmbH
          • Scharpenberger Strasse 96-98
          • 58256 Ennepetal
          • Deutschland

          • 02333-79050
            02333-790555
          • sales@wirths.net
            www.wirths.net
          #1041-1111180 · Bed Type Milling Machine - Universal

          WEILER - FHP 750 - - 1975 -

          Technical details
          x-travel 0550 mm︱y-travel 180 mm︱z-travel 300 mm︱table-size vorsch mm︱feed: 15/5 - 750/250 mm/min︱rapid traverse 5,5 m/min︱spindle turning speed range 40- 2000 U/min︱tool taper SK 40 ︱total power requirement 3 kW︱weight of the machine ca. 1,3 t︱dimensions of the machine ca. 2,1 x 1,4 x 1,7 m︱
          Programable Production milling machine with horizontal milling spindle and with additional vertical milling head.
            x-travel 0550 mm
            y-travel 180 mm
            z-travel 300 mm
            table-size vorsch mm
            feed: 15/5 - 750/250 mm/min
            rapid traverse 5,5 m/min
            spindle turning speed range 40- 2000 U/min
            tool taper SK 40
            total power requirement 3 kW
            weight of the machine ca. 1,3 t
            dimensions of the machine ca. 2,1 x 1,4 x 1,7 m
            Description :
            Programable Production milling machine with horizontal milling spindle and with
            additional vertical milling head.
          Datasheet
          Request / Contact
          •   
          •   
          • 1  
          • 2  
          • 3  
          • 4  
          •   
          •   

            Trader Profile:   Karl Günter Wirths GmbH

          Contact Trader



            Karl Günter Wirths GmbH
           Scharpenberger Strasse 96-98
            58256 - Ennepetal
            Deutschland
            02333-79050">02333-79050
            02333-790555
            sales@wirths.net
            www.wirths.net

          Profile of Trader

          About us - Wirths GmbH in Ennepetal

          wirths gmbh.Karl G. Wirths founded the company in 1956 as a mechanical workshop. 1961 he developed a die shop for pressing and forming dies. In that time 30 employees were working as die makers in the work shop.
           
          Parallel Karl G. Wirths started a shop for refurbishment of machine tools. That was also the start for the machine tool business.

          The die shop was closed 1972 but the machine tool business was developed.

          In 1972 the first stock was erected. Up to now buildings with up to 50 t crane capacity.

          In that stock we always keep approx. 250 machines.

          We are not focused on a one time business but on a long term business relative with our domestic customers and customers from all places around the world.

          Contact us

          Wirths GmbHKarl Günter Wirths GmbH
          Scharpenberger Str. 96-98
          D-58256 Ennepetal / Germany




          Karl Günter Wirths GmbH   58256 - Ennepetal Scharpenberger Strasse 96-98 Deutschland
          Karl Günter Wirths GmbH

          Scharpenberger Strasse 96-98



          Contact Trader


            Karl Günter Wirths GmbH
           Scharpenberger Strasse 96-98
            58256 - Ennepetal
            Deutschland
            02333-79050
            02333-790555
            sales@wirths.net
            www.wirths.net
            Contact person:

           
          ACHTUNG: NEUE FAX Nr. 02333 790555




          Machine category


          Abkantpresse - hydraulisch · Anreißplatte · Aufspannplatte · Bandschleifmaschine · Bandsäge - horizontal · Bearbeitungszentrum - Universal · Bettfräsmaschine - Universal · Bohrwerkstisch · Bügelsäge · Bügelsäge - Automatisch · CNC Drehmaschine · Doppelständerpresse - Hydraulisch · Doppelständerziehpresse - Hydraulisch · Drehmaschine - zyklengesteuert · Einständerexzenterpresse · Endenbearbeitungsmaschine · Flachschleifmaschine - Horizontal · Fräsmaschine - Universal · Handhebel-Schere · Honmaschine - Innen - Horizontal · Karusselldrehmaschine - Einständer · Kreissäge - Automatisch · Messmaschine · Messplatte · Nuten-Stossmaschine · Pneumatische Presse · Profilstahlschere - Kombiniert · Querteilanlage · Richtmaschine · Richtplatte · Richtpresse - Einständer · Schaufelbagger · Schnellradialbohrmaschine · Spitzendrehmaschine · Stangenzuführung · Stanzautomat-Doppelständer · Tafelschere - hydraulisch · Zahnrad-Abwälzfräsmaschine - vertikal ·