Single Column Press - Hydraulic

stroke 400 mm︱Capacity 100 T︱Table length 800 mm︱Table width 500 mm︱Machine dimensions (lxwxh) 1700 x 1700 x 2850 mm︱Machine weight 5500 kg︱

---

CNC controlled With CE mark and security Motor: 11 kW Pressure: 240 Bar Speed forward of the ram table: 110 mm / Ram table return speed: 170 mm / sn Cylinder: 220 mm Pump: 27.5 l / min Max. Dim. workpiece: 800 x 500 mm Max. workpiece weight: 5000 kg

pressure 025 t︱throat 290 mm︱stroke 200 mm︱distance table/ram 400 (500) mm︱hole in the table 60 mm︱table height over floor 940 mm︱ram surface mm︱feed down 150 mm/sec︱feed up 150 mm/sec︱working feed 18 mm/sec︱table surface area 650 x 450 mm︱oil volume 350 l︱total power requirement 11,0 kW︱weight of the machine ca. 5,2 t︱dimensions of the machine ca. 0,80 x 1,80 x 3,20 m︱

---

Equipment: UVV: approved for manual inlay work CE standard - EN 693, BGR 500 Sick photocell Mechanical depth stop; adjustable by motor Two-hand and foot control Control: Siemens S 7 / Pilz PNOZ * WITH start up the machine at the current location in the given condition *

100 to︱ 600 x 500 mm︱ 400 mm︱ 500 mm︱ 600 x 420 mm︱ 15 kW︱ 1.100 mm︱ 1.600 mm︱ 2.700 mm︱ 5.000 kg︱

---

main cylinder + 2 support cylinders hydraulic block, hydraulic valves, hydraulic pump: Rexroth control Siemens S7-300 with 7“ screen safety PLC: Sick oil/water cooler sensors for upper and lower dead stop in- and output signals for external connenction 24V without 2 hand control and without light guard - concepted to operate in a closed cell users manual in GERMAN Doeas not comply with the current industrial safety regulations (AMVO & UVV) / no CE press force: 100 to work dimension: 600 x 500 mm stroke: 400 mm distance ram-table: 500 mm working speed: 9,9 mm/sec. approach speed: 100 mm/sec. return speed: 170 mm/sec. table: 600 x 420 mm motor: 15 kW length: 1.100 mm width: 1.600 mm heigth: 2.700 mm weight: 5.000 kg

pressure 30 t︱throat mm︱stroke 250 mm︱-------------------------------------------------- ︱PRESS DESIGN ︱- drive system: hydraulic ︱- opening in table: yes ︱PRESS FORCES ︱- total force (nominal) 30 to︱PRESS TABLE ︱- table surface (left-right) 700 mm︱- table surface (front-back) 500 mm︱- thickness of bolster plate 100 mm︱SLIDE ︱- slide force 30 to︱- table surface (left-right) 500 mm︱- table surface (front-back) 400 mm︱- stroke 250 mm︱- thickness of bolster plate 100 mm︱SLIDE (HYDR. PRESS) ︱

---

pressure 100 t︱throat 360 mm︱stroke 600 mm︱distance table/ram 900 mm︱hole in the table 120 mm︱table height over floor 900 mm︱ram surface 800 x 600 mm︱feed down mm/sec︱feed up mm/sec︱working feed mm/sec︱table surface area 1050 x 700 mm︱oil volume 650 l︱total power requirement 30,0 kW︱weight of the machine ca. 14,0 t︱dimensions of the machine ca. 1,80 x 2,80 x 3,60 m︱

---

Equipment: UVV: approved for manual inlay work CE standard - EN 693, BGR 500 Sick photocell Two-hand operation * WITH start up the machine at the current location * WITH new control Siemens S7-1500 F, comfort control via touch panel Execution of the control according to EN 692 or EN 693

pressure 6 t︱throat 300 mm︱stroke mm︱table surface area 400 x 500 mm︱ram surface 350 x 500 mm︱weight of the machine ca. 1,6 t︱dimensions of the machine ca. 1,1 x 1,4 x 2,6 m︱total power requirement kW︱

---

pressure 50 t︱stroke 150 mm︱table surface area 480x350 mm︱ram surface 480x350 mm︱hole in the table Ø 75 mm︱table height 850 mm︱tool hole in ram Ø 50 mm︱weight of the machine ca. 4 t︱dimensions of the machine ca. 2000x2000x2500 mm︱

---

pressure 040 t︱throat 320 mm︱stroke 300 mm︱distance table/ram 500 mm︱hole in the table 80 mm︱table height over floor 900 mm︱ram surface 450 x 400 mm︱feed down mm/sec︱feed up mm/sec︱working feed mm/sec︱table surface area 640 x 620 mm︱oil volume 300 l︱total power requirement 5,5 kW︱weight of the machine ca. 3,6 t︱dimensions of the machine ca. 1,10 x 1,70 x 2,70 m︱

---

Equipment: UVV: approved for manual inlay work CE standard - EN 693, BGR 500 Controllable depending on pressure, time and travel Adjustable working speed Two-hand operation * WITH start up the machine at the current location in the given condition *

pressure 100 t︱throat 360 mm︱stroke 500 mm︱table surface area 740x560 mm︱ram surface 530x400 mm︱tool hole in ram Ø 40 mm︱weight of the machine ca. 7,0 t︱dimensions of the machine ca. 2000x1700x2850 mm︱

---

pressure 25 t︱throat 350 mm︱stroke 400 mm︱table surface area 800x500 mm︱ram surface 800x500 mm︱hole in the table 180x120 mm︱table height 860 mm︱tool hole in ram Ø 40 mm︱total power requirement 7,5 kW︱weight of the machine ca. 4,0 t︱dimensions of the machine ca. 1400x1800x3400 mm︱

---

pressure 10 t︱throat 0 mm︱stroke 400 mm︱total power requirement 7,5 kW︱weight of the machine ca. 6500 t︱dimensions of the machine ca. m︱

---

D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weight, approx. 6,500 kg Accessories / Special Features * DUNKES CNC Control, Model 200, can be programmed with presettable parameters, e.g. Stroke, speed, forward and return motion, pressing time, etc. * Separate switch cabinet with floppy disk input. * Pendant control with monitor. * Two-handed release, in conjunction with pneumatic safety door. * A turning device for calibrating and smoothing of bores is mounted on the ram. (Calibrating mandrel moves into the bore and rotates, powered by it own motor-driven timer. Repetitions are controlled by stroke counter.)

pressure 75 t︱throat 280 mm︱stroke 303 mm︱total power requirement 15 kW︱weight of the machine ca. 7000 kg︱dimensions of the machine ca. m︱

---

pressure 6 t︱throat 120 mm︱stroke 80 mm︱Table length 280 mm︱Table width 200 mm︱

---

Pneumatic

pressure 40 t︱throat 320 mm︱stroke 250 mm︱arm length 320 mm︱table surface area 1400x600 mm︱ram surface 1200x600 mm︱dayligth 650 mm︱total power requirement 22 kW︱weight of the machine ca. 8 t︱dimensions of the machine ca. 3200x3300x3300 m︱

---

pressure 060 t︱throat 400 mm︱stroke 600 mm︱distance table/ram 700 mm︱hole in the table mm︱table height over floor 850 mm︱ram surface 700 x 700 mm︱feed down mm/sec︱feed up mm/sec︱working feed mm/sec︱table surface area 1120 x 700 mm︱oil volume 275 l︱total power requirement 7,5 kW︱weight of the machine ca. 7,3 t︱dimensions of the machine ca. 1,60 x 2,00 x 3,70 m︱

---

Equipment: UVV: approved for manual inlay work UVV 11.064 - VBG 7n5.2 § 20 Control: Siemens S 5 * WITH start up the machine at the current location in the given condition *

pressure 25 t︱throat 250 mm︱stroke 100 mm︱total power requirement 7,5 kW︱weight of the machine ca. 3200 kg︱dimensions of the machine ca. 1000 x 1700 x 2600 m︱

---

pressure 003,15 t︱table width 400 mm︱table depth 450 mm︱stroke 280 mm︱throat 150 mm︱dayligth 500 mm︱hole in the table 100 mm︱weight of the machine ca. 0,5 t︱table height over floor 800 mm︱feed down 100 mm/sec︱feed up 300 mm/sec︱

---

pressure 003,15 t︱table width 400 mm︱table depth 450 mm︱stroke 280 mm︱throat 150 mm︱dayligth 500 mm︱hole in the table 100 mm︱weight of the machine ca. 0,5 t︱table height over floor 800 mm︱feed down 100 mm/sec︱feed up 300 mm/sec︱

---

pressure - ︱throat - ︱stroke - ︱

---

pressure 40 t︱throat 365 mm︱stroke 400 mm︱table surface area 800x500 mm︱ram surface 520x150 mm︱hole in the table 180x120 mm︱table height 850 mm︱tool hole in ram Ø 40 mm︱total power requirement 15 kW︱weight of the machine ca. 5 t︱dimensions of the machine ca. 1500x2500x3400 mm︱

---

pressure 6,3 t︱throat 210 mm︱stroke 200 mm︱distance table/ram, max. stroke up, adjustment up 300 mm︱table surface area 380 x 350 mm︱hole in the table 100 mm︱table height over floor 1050 mm︱ram surface 45 mm︱total power requirement 4 kW︱weight of the machine ca. 0,8 t︱dimensions of the machine ca. 1,2 x 0,8 x 2,6 m︱

---

with oilhydr. Drive, hydraulic. and electr. control with UVV standardl, upper and lower travel limit, cotrolable depending on pressure time and travel, two-hand operation, mechanical depth stop, electrical cabinet, Our listing price includes commissioning of the machine in our warehouse and demonstration of Functions without tools, otherwise as the press stands and lies, ex warehouse free on truck

pressure 160 t︱throat 360 mm︱stroke 500 mm︱feed down 200 mm/sec︱feed up 250 mm/sec︱max. distance table - ram 1000 mm︱table surface area 900 x 630 mm︱ram surface 750 x 450 mm︱hole in the table 250 mm︱total power requirement 20,5 kW︱weight of the machine ca. 7,5 t︱dimensions of the machine ca. 1,25 x 2,2 x 3,45 m︱

---

pressure 65 t︱throat 220 mm︱stroke 150 mm︱table surface area 580x350 mm︱ram surface 490x280 mm︱hole in the table 180x180 mm︱table height 860 mm︱tool hole in ram Ø 40 mm︱weight of the machine ca. 3,0 t︱dimensions of the machine ca. 1300x1500x2500 mm︱

---

pressure 100 t︱throat 380 mm︱stroke 650 mm︱distance table/ram, max. stroke up, adjustment up 950 mm︱table surface area 800 x 700 mm︱table height over floor 920 mm︱ram surface 630 x 600 mm︱feed down 65 mm/sec︱feed up 375 mm/sec︱working feed 17 mm/sec︱oil volume 350 l︱power capacity 18,5 kW︱weight of the machine ca. 9 t︱dimensions of the machine ca. 2,50 x 1,50 x 4,00 m︱

---

Our list price is inclusive putting the machine in our warehouse and demonstration of the functions without tools, in Otherwise as is where is, free loaded on truck with hydr. Drive, hydr. (§ 20) and electrical control according to UVV, pressure, time and controllable dependent, upper and lower travel limit, cabinet