European network of stockholding machinery dealers

Category:
    Manufacturer:
      Machines:
        Trader:

          Mager & Wedemeyer Werkzeugmaschinen GmbH - Stockist for used machines

          Machinelist:


          Center Lathe

          used  Center Lathe PINACHO ML 18 250 x1000


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-310054 · Center Lathe

          PINACHO - ML 18 250 x1000 - - 2018 -

          Technical details
          turning diameter over bed 502 mm︱turning diameter over slide rest 310 mm︱turning length 1000 mm︱centre height 250 mm︱swing diameter over bed slide 440 mm︱bed width 300 mm︱upper slide travel cross 250 mm︱travel of upper support 130 mm︱spindle nose A2 DIN 55026 Form A ︱spindle bore 58 mm︱transmission ratio 3 ︱spindle turning speed - stepless 40 - 2080 U/min︱tailstock quill taper MT 4 ︱tailstock quill diameter 68 mm︱tailstock quill adjustment 200 mm︱main drive 5,5 kW︱coolant pump 0,1 kW︱turning tool - shaft cross cut 25 x 25 mm︱total power requirement ca. 6 kW︱weight of the machine ca. 1,52 t︱
          demonstration machine
            turning diameter over bed 502 mm
            turning diameter over slide rest 310 mm
            turning length 1000 mm
            centre height 250 mm
            swing diameter over bed slide 440 mm
            bed width 300 mm
            upper slide travel cross 250 mm
            travel of upper support 130 mm
            spindle nose A2 DIN 55026 Form A
            spindle bore 58 mm
            transmission ratio 3
            spindle turning speed - stepless 40 - 2080 U/min
            tailstock quill taper MT 4
            tailstock quill diameter 68 mm
            tailstock quill adjustment 200 mm
            main drive 5,5 kW
            coolant pump 0,1 kW
            turning tool - shaft cross cut 25 x 25 mm
            total power requirement ca. 6 kW
            weight of the machine ca. 1,52 t
            Description :
            demonstration machine
          Datasheet
          Request / Contact

          CNC Lathe

          used  CNC Lathe PINACHO STH 400x2000


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09176F · CNC Lathe

          PINACHO - STH 400x2000 - - 2019 - FAGOR 8055i FL-TC

          Technical details
          turning diameter 805 mm︱turning length 2000 mm︱control FAGOR 8055i FL-TC ︱bed width 475 mm︱centre height 400 mm︱max. swing diameter over bed 805 mm︱swing diameter over slide guides max 720 mm︱max. turning dia. over cross-slide 515 mm︱x-axis 400 mm︱rapid traverse X-axis 10 m/min︱rapid traverse Z-axis 10 m/min︱spindle nose ASA A2-8 ︱spindle passage 105 mm︱tail stock ︱diameter of quill 106 mm︱tailstock quill stroke 215 mm︱tailstock quill taper MT 6 ︱Tool turret 1 ︱Numbers of tools 8 ︱tool taper VDI 40
          First commissioning 01/2020 Technical specifications: Machine lamp, complete machine cladding with chip tray, Coolant device, servo spindle motor, Automatic lubrication of the guide Electronic handwheels for X and Z axes, CE conform, documentation Incl. Options: - Chip conveyor 2000 mm - Hydraulic kit with 3 jaw lathe chucks Ø 400 mm - 8 stations tool turret VDI 40 - mitl. Center punch MT 6 - MPG Fagor HBA portable handwheel - 6 bar cooling system - AC panel cooler - Larger memory card for FAGOR control - Set / 3 pieces additional shafts for the standard steady rest: - Machine without warranty - - all dimensions, weight and performance specifications are non-binding - - Used machine without warranty -
            turning diameter 805 mm
            turning length 2000 mm
            control FAGOR 8055i FL-TC
            bed width 475 mm
            centre height 400 mm
            max. swing diameter over bed 805 mm
            swing diameter over slide guides. 720 mm
            max. turning dia. over cross-sli. 515 mm
            x-axis 400 mm
            rapid traverse X-axis 10 m/min
            rapid traverse Z-axis 10 m/min
            spindle nose ASA A2-8
            spindle passage 105 mm
            diameter of quill 106 mm
            tailstock quill stroke 215 mm
            tailstock quill taper MT 6
            Tool turret 1
            Numbers of tools 8
            tool taper VDI 40
            Description :
            First commissioning 01/2020

            Technical specifications:

            Machine lamp, complete machine cladding with chip tray,
            Coolant device, servo spindle motor,
            Automatic lubrication of the guide
            Electronic handwheels for X and Z axes, CE conform,
            documentation

            Incl. Options:
            - Chip conveyor 2000 mm
            - Hydraulic kit with 3 jaw lathe chucks Ø 400 mm
            - 8 stations tool turret VDI 40
            - mitl. Center punch MT 6
            - MPG Fagor HBA portable handwheel
            - 6 bar cooling system
            - AC panel cooler
            - Larger memory card for FAGOR control
            - Set / 3 pieces additional shafts for the standard steady rest:

            - Machine without warranty -
            - all dimensions, weight and performance specifications are non-binding -
            - Used machine without warranty -
          Datasheet
          Request / Contact

          milling machining centers - horizontal

          used  milling machining centers - horizontal MAZAK FH-7800


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09163F · milling machining centers - horizontal

          MAZAK - FH-7800 - - 2001 - PC Fusion 640 M

          Technical details
          x-travel 1050 mm︱y-travel 800 mm︱z-travel 825 mm︱Control PC Fusion 640 M ︱size of pallet 800 x 630 mm︱table load 1,27 t︱table clamping surface: 24 x M16x2, Abstand 125 mm︱swivelling range 0,001° x 360000 Grad︱table height over floor 1250 mm︱Distance spindle nose - palett surface 200 - 1025 mm︱Distance spindle centre - table surface 50 - 850 mm︱feed range 1 - 40000 mm/min︱rapid travel x/y/z 40 m/min︱turning speed range 35 - 10000 U/min︱max. torque on the spindle 525 Nm︱power capacity - milling spindle 37 / 22 kW︱tool taper HSK 100 ︱chain magazin for tools 80 ︱diameter of tools max. 135 mm︱max. tool-dia with free toolbox 260 mm︱
          Standardzubehör: - Indexier-Tisch 0,001° x 360000 Positionen - 2-fach Palettenwechsler - Sicherheitsabdeckung für 2-fach Palettenwechsler - Kettenmagazin für 40 Werkzeuge - Werkzeuglängen-Meßeinrichtung - Komplettes Kühlmittelsystem: Flutkühlung Kühlung durch Spindel Niagara-Kühl-/Spülsystem - Ausblaseinrichtung (Hauptspindelaufnahme) - Kühlmittel- und Späneschutz durch voll gekapselten Arbeitsraum - CNC Steuerung Mazatrol PC FUSION CNC 640M Dialogprogrammierung mit Farbgrafikbildschirm) - MAZAK Monitoring System C (AFC, TBR, TLM): Adaptive Vorschubsteuerung (AFC) Werkzeugbruchüberwachung (TBR) Werkzeugstandzeitüberwachung und Ersatzwerkzeugaufruf (TLM) - Navigations Überwachungsanzeige - Bearbeitungsnavigation - PCMCIA Schnittstelle - Autom. Trenntür Öffnen/Schließen - Arbeitsraumtür-Verrieglung - Arbeitsraumbeleuchtung - 1 Satz Anleitungen Kühlmitteleinrichtung: Tankinhalt: 900 l Flutkühlung: Düsen am Spindelkopf Kühlung durch Spindel: Fördermenge an der Pumpe: ca. 30 l/min Druck an der Pumpe: ca. 5.5 bar Pumpe: 730 W Niagara-Kühl-/-Spülsystem: Düsen oben im Arbeitsraum Fördermenge an der Pumpe: ca. 100 l/min Pumpe: 560 W Spüleinrichtung für Verkleidung: Düsen an der X- und Z-Achsenverkleidung Fördermenge an der Pumpe ca. 100 l/min Pumpe 560 W Optionen: Luftblaseinrichtung für Werkstück hydr. Anschlüsse für Spannvorrichtung Linearmeßsystem für X-, Y- und Z-Achse System mit geschlossenem Regelkreis, das den tatsächlichen Ist-Positionsbetrag der X-, Y- und Z-Achse misst und eine Korrektur gemäß den Befehlwert vornimmt. Mazak Monitoring System B EIA/ISO, Dynamische Korrektur Bei der Bearbeitung mit drehendem NC-Rundtisch (B-Achsenbearbeitung) sollte das Werkstück nach der Zentrierbohrung der Palette ausgerichtet sein. Mit dieser Option, - wenn die Differenz zwischen Tischmitte- und Werkstückmittepositionen innerhalb von 3 mm wäre, werden diese durch Eingabe von Korrekturwerten automatisch korrigiert. Die zeitaufwendige Ausrichtarbeit wird dadurch reduziert. (Für NC- Tischausführung) NC-Rundtisch (Vierte Achse /0,001 x 360.000 Pos.) Drehmomentabhängiger Bohrzyklus (Mazatrol) Automatische Ermittlung der Bohrtiefeninkremente nach Drehmomenterfassung. (Vorzugsweise zusammen mit HSS Werkzeug) Zirkular Aufbohrzyklus Spiralförmiges Aufbohren von Passungen Interface-Set Inhalt: - Schnittstelle für Tastatur - Schnittstelle für Maus - Schnittstelle für Drucker Nachträgliche Einbau nicht möglich CNC Optionspaket Formenbau mit IC-Card Operation Inhalt des Pakets: - Gemeinsame Variablen (600 Paar) - MAZAK Gewindebohren Tornado (EIA/ISO) - Synchrones Gewindeschneiden - EIA/ISO Eingabefunktion - EIA/ISO Sonderfunktion Spiralinterpolation (G02.1, G03.1), Korrektur des 3D Werkzeuges (G40-G42) Skalierung (G50, G51) u.a. - EIA/ISO, Konstanter Vorschub (G93) Bei Verwendung dieser Funktion bleibt die Vorschubgeschwindigkeit bei Geraden- und Kurven-Kombinationen an der Kontur konstant. - EIA/ISO Werkzeuglängenmessung (G37) - EIA/ISO, Programmeinheit Stop Funktion Programmablauf wird bei vorgegebener Programmeinheit automatisch gestoppt. - Schnittstelle für den Hochgeschwindigkeits-Datentransfer (Ausführung RS232C, PROTOCOL B, Bautrate 19,200) Für Nachladebetrieb von überlangen EIA/ISO-Programmen mit kleinen Inkrementen. - MAZACC-3D (EIA/ISO) Präzisions-Steuerfunktion + Hochgeschwindigkeitsfunktion zur Erzielung von theoretischen Vorschubgeschwindigkeiten bis zu 134 m/min. Die Datenverarbeitungsgeschwindigkeit der Steuerung wird durch diese Option erhöht. Dies ermöglicht eine verbesserte dreidimensionale Bearbeitung sowie eine Reduzierung der Bearbeitungszeiten. - Zusätzliches Werkstückkoordinatensystem (G54.1 P1 - 48) 48 Paare - Spiralbearbeitungsfunktion (G33)für Ausdrehkopfbearbeitung (z.B. mit d'Andrea-Werkzeug) - Spline Korrekturfunktion (G06.1) - IC Speicherkarte Operation Schnittstelle für das Abarbeiten von überlangen EIA/ISO Programmen. Programme müssen auf der IC-Card gespeichert werden. (ohne IC-Card) Mayfran Modell CONSEP 2000 Kühlmittelreinigungs- und Späneförderanlage einschl. 3 Druckstufen max. 50 bar und maschinen- seitiger Vorbereitung
            x-travel 1050 mm
            y-travel 800 mm
            z-travel 825 mm
            Control PC Fusion 640 M
            size of pallet 800 x 630 mm
            table load 1,27 t
            table clamping surface: 24 x M16x2, Abstand 125 mm
            swivelling range 0,001° x 360000 Grad
            table height over floor 1250 mm
            Distance spindle nose - palett s. 200 - 1025 mm
            Distance spindle centre - table . 50 - 850 mm
            feed range 1 - 40000 mm/min
            rapid travel x/y/z 40 m/min
            turning speed range 35 - 10000 U/min
            max. torque on the spindle 525 Nm
            power capacity - milling spindle 37 / 22 kW
            tool taper HSK 100
            chain magazin for tools 80
            diameter of tools max. 135 mm
            max. tool-dia with free toolbox 260 mm
            Description :
            Standardzubehör:
            - Indexier-Tisch 0,001° x 360000 Positionen
            - 2-fach Palettenwechsler
            - Sicherheitsabdeckung für 2-fach Palettenwechsler
            - Kettenmagazin für 40 Werkzeuge
            - Werkzeuglängen-Meßeinrichtung
            - Komplettes Kühlmittelsystem:
            Flutkühlung
            Kühlung durch Spindel
            Niagara-Kühl-/Spülsystem
            - Ausblaseinrichtung (Hauptspindelaufnahme)
            - Kühlmittel- und Späneschutz durch voll gekapselten Arbeitsraum
            - CNC Steuerung Mazatrol PC FUSION CNC 640M Dialogprogrammierung mit
            Farbgrafikbildschirm)
            - MAZAK Monitoring System C (AFC, TBR, TLM):
            Adaptive Vorschubsteuerung (AFC)
            Werkzeugbruchüberwachung (TBR)
            Werkzeugstandzeitüberwachung und Ersatzwerkzeugaufruf (TLM)
            - Navigations Überwachungsanzeige
            - Bearbeitungsnavigation
            - PCMCIA Schnittstelle
            - Autom. Trenntür Öffnen/Schließen
            - Arbeitsraumtür-Verrieglung
            - Arbeitsraumbeleuchtung
            - 1 Satz Anleitungen

            Kühlmitteleinrichtung:
            Tankinhalt: 900 l
            Flutkühlung: Düsen am Spindelkopf
            Kühlung durch Spindel:
            Fördermenge an der Pumpe: ca. 30 l/min
            Druck an der Pumpe: ca. 5.5 bar
            Pumpe: 730 W
            Niagara-Kühl-/-Spülsystem: Düsen oben im Arbeitsraum
            Fördermenge an der Pumpe: ca. 100 l/min
            Pumpe: 560 W
            Spüleinrichtung für Verkleidung:
            Düsen an der X- und Z-Achsenverkleidung
            Fördermenge an der Pumpe ca. 100 l/min
            Pumpe 560 W

            Optionen:
            Luftblaseinrichtung für Werkstück
            hydr. Anschlüsse für Spannvorrichtung

            Linearmeßsystem für X-, Y- und Z-Achse
            System mit geschlossenem Regelkreis, das
            den tatsächlichen Ist-Positionsbetrag
            der X-, Y- und Z-Achse misst und eine
            Korrektur gemäß den Befehlwert vornimmt.

            Mazak Monitoring System B

            EIA/ISO, Dynamische Korrektur
            Bei der Bearbeitung mit drehendem NC-Rundtisch (B-Achsenbearbeitung) sollte das
            Werkstück nach der Zentrierbohrung der Palette ausgerichtet sein. Mit
            dieser Option, - wenn die Differenz zwischen Tischmitte- und
            Werkstückmittepositionen innerhalb von 3 mm wäre, werden diese durch Eingabe
            von Korrekturwerten automatisch korrigiert.
            Die zeitaufwendige Ausrichtarbeit wird dadurch reduziert. (Für NC-
            Tischausführung)

            NC-Rundtisch (Vierte Achse /0,001 x 360.000 Pos.)

            Drehmomentabhängiger Bohrzyklus (Mazatrol)
            Automatische Ermittlung der Bohrtiefeninkremente nach Drehmomenterfassung.
            (Vorzugsweise zusammen mit HSS Werkzeug)

            Zirkular Aufbohrzyklus
            Spiralförmiges Aufbohren von Passungen

            Interface-Set
            Inhalt:
            - Schnittstelle für Tastatur
            - Schnittstelle für Maus
            - Schnittstelle für Drucker
            Nachträgliche Einbau nicht möglich

            CNC Optionspaket Formenbau mit IC-Card Operation
            Inhalt des Pakets:
            - Gemeinsame Variablen (600 Paar)
            - MAZAK Gewindebohren Tornado (EIA/ISO)
            - Synchrones Gewindeschneiden
            - EIA/ISO Eingabefunktion
            - EIA/ISO Sonderfunktion
            Spiralinterpolation (G02.1, G03.1),
            Korrektur des 3D Werkzeuges (G40-G42)
            Skalierung (G50, G51) u.a.
            - EIA/ISO, Konstanter Vorschub (G93)
            Bei Verwendung dieser Funktion bleibt
            die Vorschubgeschwindigkeit bei
            Geraden- und Kurven-Kombinationen an
            der Kontur konstant.
            - EIA/ISO Werkzeuglängenmessung (G37)
            - EIA/ISO, Programmeinheit Stop Funktion
            Programmablauf wird bei vorgegebener
            Programmeinheit automatisch gestoppt.
            - Schnittstelle für den Hochgeschwindigkeits-Datentransfer
            (Ausführung RS232C, PROTOCOL B, Bautrate 19,200)
            Für Nachladebetrieb von überlangen EIA/ISO-Programmen mit kleinen Inkrementen.
            - MAZACC-3D (EIA/ISO)
            Präzisions-Steuerfunktion + Hochgeschwindigkeitsfunktion zur Erzielung
            von theoretischen Vorschubgeschwindigkeiten bis zu 134 m/min. Die
            Datenverarbeitungsgeschwindigkeit der Steuerung wird durch diese Option
            erhöht. Dies ermöglicht eine verbesserte dreidimensionale Bearbeitung sowie
            eine Reduzierung der Bearbeitungszeiten.
            - Zusätzliches Werkstückkoordinatensystem (G54.1 P1 - 48) 48 Paare
            - Spiralbearbeitungsfunktion (G33)für Ausdrehkopfbearbeitung
            (z.B. mit d'Andrea-Werkzeug)
            - Spline Korrekturfunktion (G06.1)
            - IC Speicherkarte Operation
            Schnittstelle für das Abarbeiten von überlangen EIA/ISO Programmen.
            Programme müssen auf der IC-Card gespeichert werden. (ohne IC-Card)

            Mayfran Modell CONSEP 2000
            Kühlmittelreinigungs- und Späneförderanlage
            einschl. 3 Druckstufen max. 50 bar und maschinen-
            seitiger Vorbereitung
          Datasheet
          Request / Contact

          milling machining centers - vertical

          used  milling machining centers - vertical MAZAK VTC-200BII


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09174F · milling machining centers - vertical

          MAZAK - VTC-200BII - - 2011 - PC-Fusion-640M

          Technical details
          x-travel 1120 mm︱y-travel 510 mm︱z-travel 510 mm︱Control PC-Fusion-640M ︱spindle taper SK 40 ︱spindle turning speed range 40 - 12.000 U/min︱distance spindle centre table top edge 180 - 690 mm︱table load 800 Kg︱distance spindle center to column 530 mm︱rapid travel x/y/z 36 m/min︱table width 1460 mm︱table length 510 mm︱5-T-slots - width x distance 18 x 100 mm︱table height over floor 750 mm︱tool change unit 30 ︱tool changing time 4,7 sec︱wotkpiece diameter with 2 vacant positions 110 mm︱workpiece diameter at full load 80 mm︱max. tool weight 8 kg︱tool length - max. 350 mm︱
          Special accessories: - Modified front door, loading and unloading options with a crane through the front door - High pressure coolant supply through spindle (15 bar) - Optional CNC software package Performance Contains: - additional variables (600 in total) - Mazak tapping / boring cycle Tornado (EIA) - Synchronized tapping - EIA / ISO code input function - Additional EIA / ISO function - Reverse feed rate G93 - G37 automatic tool length measurement - Function for stop after block number comparison - G0 inclination constant - Additional workpiece coordination systems (G54.1) - Thread cutting function -Hinged belt conveyor, ejection on the right side - all dimensions, weight and performance specifications are non-binding - GENERAL MACHINE OPTIONS - 1 set of manuals - Operation manual - Programming instructions - Maintenance instructions - AFC function, adaptable feed control - Mazak standard paint (black / gray) SAFETY DEVICES - Operator door with locking switch - Workspace cladding The splash guard encloses the work area from the side - Work area lighting attached to the top around the operator to support a safe and effective set-up of the machine - Machine with CE mark COOLANT SUPPLY - Coolant supply through spindle - Complete coolant system includes pumps, valves, pipes and nozzles for efficient Manufacturing of quality components MEASURING SYSTEM - automatic tool length measurement, the length of tools with small Diameter is measured in fully automatic mode. - Tool breakage detection, for tools with a small diameter such as drills and taps will automatically check for tool breakage performed. CHIP DISPOSAL - Preparation for chip conveyor on the side STEERING - MAZATROL PC- Fusion- CNC 640M - Edit navigation - prediction After programming, the machining time, spindle load, etc. are saved using the Navigation function predicted before the actual editing is performed. Based on this data, the program can be used for maximum productivity be optimized. - Edit navigation monitoring The current machining conditions and loads are displayed in real time displayed, with additional data output for further program optimization will. - Edit navigation result After finishing the processing, the processing results are displayed and can be compared with a preliminary calculation. NUMERIC CONTROL - Relocation Detector - 10.4 “color screen - Mazak tapping and drilling cycle Tornado (Mazatrol) By boring and tapping in helical mode Machining of a wide variety of diameters at high speed can be machined with just one workpiece. This function minimizes Programming and processing times. - RS-232C interface - Background toolpath checking The toolpath of one program can be checked even if another Program number is called and processed in automatic mode. - PCMCIA interface (2 slots) - Interface for IC memory card - 3.5 “floppy disk drive - Network interface (for LAN and modem) - Tool life monitoring When the tool life has expired, the tool can automatically counteract a replacement tool can be exchanged Other values: Rated machine power (30 min. Operation) 26.1 kVA Working spindle: AC asynchronous motor spindle drive Nominal spindle power (5 min. Operation) 18.5 kW Nominal spindle power (10 min. Operation) 15.0 kW Nominal spindle power (30 min. Operation) 11.0 kW Nominal spindle power (100% continuous operation) 7.5 kW Total weight of all magazine tools 120 kg Number of coolant tanks 1 Delivery rate at the pump 16 l / min Pressure at the pump 5 bar - Size of the reference groove 18H8 - all dimensions, weights and performance information are non-binding - - Used machine without warranty - - Subject to prior sale -
            x-travel 1120 mm
            y-travel 510 mm
            z-travel 510 mm
            Control PC-Fusion-640M
            spindle taper SK 40
            spindle turning speed range 40 - 12.000 U/min
            distance spindle centre table to. 180 - 690 mm
            table load 800 Kg
            distance spindle center to colum. 530 mm
            rapid travel x/y/z 36 m/min
            table width 1460 mm
            table length 510 mm
            5-T-slots - width x distance 18 x 100 mm
            table height over floor 750 mm
            tool change unit 30
            tool changing time 4,7 sec
            wotkpiece diameter with 2 vacant. 110 mm
            workpiece diameter at full load 80 mm
            max. tool weight 8 kg
            tool length - max. 350 mm
            Description :
            Special accessories:
            - Modified front door, loading and unloading options with a crane through the
            front door
            - High pressure coolant supply through spindle (15 bar)

            - Optional CNC software package Performance
            Contains:
            - additional variables (600 in total)
            - Mazak tapping / boring cycle Tornado (EIA)
            - Synchronized tapping
            - EIA / ISO code input function
            - Additional EIA / ISO function
            - Reverse feed rate G93
            - G37 automatic tool length measurement
            - Function for stop after block number comparison
            - G0 inclination constant
            - Additional workpiece coordination systems (G54.1)
            - Thread cutting function
            -Hinged belt conveyor, ejection on the right side
            - all dimensions, weight and performance specifications are non-binding -

            GENERAL MACHINE OPTIONS
            - 1 set of manuals
            - Operation manual
            - Programming instructions
            - Maintenance instructions
            - AFC function, adaptable feed control
            - Mazak standard paint (black / gray)

            SAFETY DEVICES
            - Operator door with locking switch
            - Workspace cladding
            The splash guard encloses the work area from the side
            - Work area lighting attached to the top around the operator
            to support a safe and effective set-up of the machine
            - Machine with CE mark

            COOLANT SUPPLY
            - Coolant supply through spindle
            - Complete coolant system
            includes pumps, valves, pipes and nozzles for efficient
            Manufacturing of quality components

            MEASURING SYSTEM
            - automatic tool length measurement, the length of tools with small
            Diameter is measured in fully automatic mode.
            - Tool breakage detection, for tools with a small diameter such as drills
            and taps will automatically check for tool breakage
            performed.

            CHIP DISPOSAL
            - Preparation for chip conveyor on the side

            STEERING
            - MAZATROL PC- Fusion- CNC 640M
            - Edit navigation - prediction
            After programming, the machining time, spindle load, etc. are saved using the
            Navigation function predicted before the actual editing
            is performed. Based on this data, the program can be used for maximum
            productivity
            be optimized.
            - Edit navigation monitoring
            The current machining conditions and loads are displayed in real time
            displayed, with additional data output for further program optimization
            will.
            - Edit navigation result
            After finishing the processing, the processing results are displayed
            and can be compared with a preliminary calculation.

            NUMERIC CONTROL
            - Relocation Detector
            - 10.4 “color screen
            - Mazak tapping and drilling cycle Tornado (Mazatrol)
            By boring and tapping in helical mode
            Machining of a wide variety of diameters at high speed
            can be machined with just one workpiece. This function minimizes
            Programming and processing times.
            - RS-232C interface
            - Background toolpath checking
            The toolpath of one program can be checked even if another
            Program number is called and processed in automatic mode.
            - PCMCIA interface (2 slots)
            - Interface for IC memory card
            - 3.5 “floppy disk drive
            - Network interface (for LAN and modem)
            - Tool life monitoring
            When the tool life has expired, the tool can automatically counteract
            a replacement tool can be exchanged


            Other values:

            Rated machine power (30 min. Operation) 26.1 kVA

            Working spindle:
            AC asynchronous motor spindle drive
            Nominal spindle power (5 min. Operation) 18.5 kW
            Nominal spindle power (10 min. Operation) 15.0 kW
            Nominal spindle power (30 min. Operation) 11.0 kW
            Nominal spindle power (100% continuous operation) 7.5 kW
            Total weight of all magazine tools 120 kg

            Number of coolant tanks 1
            Delivery rate at the pump 16 l / min
            Pressure at the pump 5 bar

            - Size of the reference groove 18H8

            - all dimensions, weights and performance information are non-binding -

            - Used machine without warranty -

            - Subject to prior sale -
          Datasheet
          Request / Contact
          used  milling machining centers - vertical MAZAK VCN 510 CII


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09172F · milling machining centers - vertical

          MAZAK - VCN 510 CII - - 2007 - Matrix Nexus

          Technical details
          x-travel 1050 mm︱y-travel 510 mm︱z-travel 510 mm︱control Matrix Nexus ︱spindle taper DIN 69871/SK40 ︱Feed speed max 36 m/min.︱turning speed range 35 - 12.000 U/min︱rapid travel x/y/z 36 m/min︱distance spindle /table max. 660 mm︱distance spindle /table min. 150 mm︱tool change unit ︱no. of tools in the magazine 30 Stück︱tool taper CAT 40 ︱Tool diameter 80 mm︱wotkpiece diameter with 2 vacant positions max. 125 mm︱max. tool weight 8 kg︱max. tool length 350 mm︱change-time chip to chip 2,9 sec︱table: ︱table length 1300 mm︱
          Control: Mazatrol Matrix Nexus Main drive power AC motor 18.5 kW at 5 min nominal power 11 kW at 10 min nominal power 15 kW at 30 min nominal power 7.5 kW with 100% continuous operation Machine color gray / black GENERAL MACHINE OPTIONS - Transformer for the European market - 12.1 ’’ LCD color screen - Mazak (standard paint (black / gray) - Main spindle motor 18.5 kW / 5 min. SAFETY DEVICES - Operator door with locking switch - Workspace cladding - Upper cover to protect against chips and chips thrown out from above Coolant during high-speed operation. - Fully paneled work area COOLANT SUPPLY - Flood cooling pressure 4.5 bar, delivery rate at the pump 30l / min. - Coolant supply through spindle, pressure 5 bar, flow rate at the pump 27l / min. - Complete coolant system, includes pumps, valves, pipes and nozzles MEASURING SYSTEM - Tool length measurement + broken tool detection - automatic tool length measurement CLAMPING TABLE / PALLET - Reference groove for the Y axis in the table CHIP DISPOSAL - Preparation for chip conveyor on the left NUMERICAL CONTROL - User macro (600 variables) - Mazak tapping / drilling cycle Tornado (Mazatrol): By boring and Tapping in helical machining mode different diameters at high speed with just one tool to be edited. This function minimizes programming and processing times - Mazak tapping / drilling cycle Tornado in EIA / ISO - EIA / ISO input function - additional EIA / ISO input function - Helical interpolation - 3D tool correction - Workpiece coordinate rotation - Geometric function - scaling - External data input / output - Reversing time feed G 93 - Optional stop (optional stop): The automatic operation is stopped when the code M01 has been programmed, the menu for optional stop is still displayed inversely. - Background toolpath checking: The toolpath of a program can be checked, even if a different program number is in automatic mode is called and processed. - MAZACC 2D software - additional workpiece coordination systems, 300 pieces - Thread cutting function: The feed of the tool is controlled synchronously for spindle rotation. It can cylindrical. u. conical threads are manufactured. - EIA / ISO drilling cycles - USB interface 2 pieces - LAN interface - intelligent heat shield Sensors determine the current temperature of the machine. A computational comparison of the data takes place on the basis of these values. - intelligent danger sign With this function, machine collisions are avoided during manual operation prevented and thus facilitates the set-up. - MAZAK language support - virtual machining Incl. the following special accessories: - Drilling cycle with torque-dependent chip breaking - Synchronous tapping - Used machine without warranty - - all dimensions, weight and performance specifications are non-binding -
            x-travel 1050 mm
            y-travel 510 mm
            z-travel 510 mm
            control Matrix Nexus
            spindle taper DIN 69871/SK40
            Feed speed max 36 m/min.
            turning speed range 35 - 12.000 U/min
            rapid travel x/y/z 36 m/min
            distance spindle /table max. 660 mm
            distance spindle /table min. 150 mm
            no. of tools in the magazine 30 Stück
            tool taper CAT 40
            Tool diameter 80 mm
            wotkpiece diameter with 2 vacant. max. 125 mm
            max. tool weight 8 kg
            max. tool length 350 mm
            change-time chip to chip 2,9 sec
            table length 1300 mm
            Description :
            Control: Mazatrol Matrix Nexus
            Main drive power AC motor
            18.5 kW at 5 min nominal power
            11 kW at 10 min nominal power
            15 kW at 30 min nominal power
            7.5 kW with 100% continuous operation

            Machine color gray / black

            GENERAL MACHINE OPTIONS
            - Transformer for the European market
            - 12.1 ’’ LCD color screen
            - Mazak (standard paint (black / gray)
            - Main spindle motor 18.5 kW / 5 min.

            SAFETY DEVICES
            - Operator door with locking switch
            - Workspace cladding
            - Upper cover to protect against chips and chips thrown out from above
            Coolant during high-speed operation.
            - Fully paneled work area

            COOLANT SUPPLY
            - Flood cooling pressure 4.5 bar, delivery rate at the pump 30l / min.
            - Coolant supply through spindle, pressure 5 bar, flow rate at the pump 27l /
            min.
            - Complete coolant system, includes pumps, valves, pipes and nozzles

            MEASURING SYSTEM
            - Tool length measurement + broken tool detection
            - automatic tool length measurement

            CLAMPING TABLE / PALLET
            - Reference groove for the Y axis in the table

            CHIP DISPOSAL
            - Preparation for chip conveyor on the left

            NUMERICAL CONTROL
            - User macro (600 variables)

            - Mazak tapping / drilling cycle Tornado (Mazatrol): By boring and
            Tapping in helical machining mode
            different diameters at high speed with just one tool
            to be edited. This function minimizes programming and processing times

            - Mazak tapping / drilling cycle Tornado in EIA / ISO

            - EIA / ISO input function

            - additional EIA / ISO input function
            - Helical interpolation
            - 3D tool correction
            - Workpiece coordinate rotation

            - Geometric function
            - scaling
            - External data input / output

            - Reversing time feed G 93

            - Optional stop (optional stop): The automatic operation is
            stopped when the code M01 has been programmed, the menu for optional stop
            is still displayed inversely.

            - Background toolpath checking: The toolpath of a program can
            be checked, even if a different program number is in automatic mode
            is called and processed.

            - MAZACC 2D software
            - additional workpiece coordination systems, 300 pieces

            - Thread cutting function: The feed of the tool is controlled synchronously
            for spindle rotation. It can cylindrical. u. conical threads are manufactured.

            - EIA / ISO drilling cycles
            - USB interface 2 pieces
            - LAN interface

            - intelligent heat shield
            Sensors determine the current temperature of the machine.
            A computational comparison of the data takes place on the basis of these
            values.

            - intelligent danger sign
            With this function, machine collisions are avoided during manual operation
            prevented and thus facilitates the set-up.

            - MAZAK language support

            - virtual machining

            Incl. the following special accessories:
            - Drilling cycle with torque-dependent chip breaking
            - Synchronous tapping

            - Used machine without warranty -
            - all dimensions, weight and performance specifications are non-binding -
          Datasheet
          Request / Contact

          Band Saw - Automatic - Horizontal

          used  Band Saw - Automatic - Horizontal MEP - VOLLAUTOMAT SHARK 350 NC HS 5.0


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-341080 · Band Saw - Automatic - Horizontal

          MEP - VOLLAUTOMAT - SHARK 350 NC HS 5.0 - - 2019 -Neu- - NC 5.0

          Technical details
          cutting diameter 350 mm︱saw band length 4640 x 34 x 1,1 mm︱cutting width 350 mm︱Control NC 5.0 ︱band speed 15 - 100 m/min︱capacity 90 degrees: square 350 x 350 mm︱table height 860 mm︱total power requirement 4 kW︱weight of the machine ca. 2,8 t︱dimensions of the machine ca. 3,1 x 2,2 x 2,2 m︱
          Shark 350 NC HS 5.0, automatic hydraulic band saw machine in two-column design for 0 ° cuts on solid material and profiles made of steel, stainless steel and steel alloys up to a maximum of 350x350 mm. The standard equipment includes: - Driven chip conveyor, can be installed on the right or left of the machine - Clamping pressure regulation of the vices - Feeder with vertical rollers for lateral material support - Numerically controlled band saw machines, which can also be operated semi- automatically, with the new MEP 50, specially developed by MEP for automatic machines, Windows "CE" based control. Cutting cycle “clean cut” The feeder pushes the workpiece backwards in order to avoid scoring at the cutting surface when the belt moves up again at the end of the cut. - Fieldbus communication system with double microprocessor and serial connection. - The user interface with 7 ”touch screen display and mechanical keys are used for the operating functions of the sawmasc ins, guarantees a reliable, simple and intuitive use, as well as a real-time control of all cutting parameters standard equipment - Shark 350 NC
            cutting diameter 350 mm
            saw band length 4640 x 34 x 1,1 mm
            cutting width 350 mm
            Control NC 5.0
            band speed 15 - 100 m/min
            capacity 90 degrees: square 350 x 350 mm
            table height 860 mm
            total power requirement 4 kW
            weight of the machine ca. 2,8 t
            dimensions of the machine ca. 3,1 x 2,2 x 2,2 m
            Description :
            Shark 350 NC HS 5.0, automatic hydraulic band saw machine in two-column design
            for 0 ° cuts on solid material and profiles made of steel, stainless steel and
            steel alloys
            up to a maximum of 350x350 mm. The standard equipment includes:
            - Driven chip conveyor, can be installed on the right or left of the machine
            - Clamping pressure regulation of the vices
            - Feeder with vertical rollers for lateral material support
            - Numerically controlled band saw machines, which can also be operated semi-
            automatically,
            with the new MEP 50, specially developed by MEP for automatic machines,
            Windows "CE" based control. Cutting cycle “clean cut” The feeder pushes the
            workpiece
            backwards in order to avoid scoring at the cutting surface when the belt moves
            up again at
            the end of the cut. - Fieldbus communication system with double microprocessor
            and serial connection.
            - The user interface with 7 ”touch screen display and mechanical keys are used
            for the operating functions
            of the sawmasc ins, guarantees a reliable, simple and intuitive use, as well as
            a real-time control of all
            cutting parameters standard equipment - Shark 350 NC
          Datasheet
          Request / Contact
          used  Band Saw - Automatic - Horizontal MEP - VOLLAUTOMAT SHARK 331-1 NC SPIDER 5.0


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-341072 · Band Saw - Automatic - Horizontal

          MEP - VOLLAUTOMAT - SHARK 331-1 NC SPIDER 5.0 - - 2017 -Neu- - Evolution TS 50

          Technical details
          cutting diameter 280 mm︱saw band length 3320 x 27 x 0,9 mm mm︱cutting width 330 mm︱Control Evolution TS 50 ︱band speed 15 - 100 m/min︱capacity 90 degrees: round 280 mm︱capacity 90 degrees: square 260 x 260 mm︱capacity 90 degrees: flat 330 x 260 mm︱capacity 45 degrees: round 260 mm︱capacity 45 degrees: square 250 mm︱capacity 45 degrees: flat 270 x 200 mm︱capacity 60 degrees: round 180 mm︱capacity 60 degrees: square 170 mm︱capacity 60 degrees: flat 170 x 170 mm︱total power requirement 2,2 kW︱weight of the machine ca. 1,24 t︱dimensions of the machine ca. 3,3 x 2,83 x 2,23 m︱
          Electro-hydraulic automatic miter band saw for cuts from 0 ° to 60 ° left. Maximum performance in the smallest of spaces - Miter cuts up to 60 ° left possible - Saw band length: 3650x27x0.9 - single stroke: 600 mm (programmable up to 10m) - Simple 7 "touchscreen operation NC 5.0. - Saw arm made of spheroidal cast iron - robust and stable - Required space 3.4 m² - Footprint 1900mm wide x 1800mm deep With the new Shark 331 NC 5.0 Spider, MEP proves the high Performance requirement and maximum ease of use have a compact design can without foregoing all the components that ensure the safety of the Ensure operating personnel. Innovative (Windows CE based) 7 "touch screen control for easy and quick setting of all machine parameters and with additional software Keys for common functions Controlled head descent with automatic compensation via one in the cylinder mounted servo valve through constant monitoring of the torque and with precise setting in millimeters / minute
            cutting diameter 280 mm
            saw band length 3320 x 27 x 0,9 mm mm
            cutting width 330 mm
            Control Evolution TS 50
            band speed 15 - 100 m/min
            capacity 90 degrees: round 280 mm
            capacity 90 degrees: square 260 x 260 mm
            capacity 90 degrees: flat 330 x 260 mm
            capacity 45 degrees: round 260 mm
            capacity 45 degrees: square 250 mm
            capacity 45 degrees: flat 270 x 200 mm
            capacity 60 degrees: round 180 mm
            capacity 60 degrees: square 170 mm
            capacity 60 degrees: flat 170 x 170 mm
            total power requirement 2,2 kW
            weight of the machine ca. 1,24 t
            dimensions of the machine ca. 3,3 x 2,83 x 2,23 m
            Description :
            Electro-hydraulic automatic miter band saw
            for cuts from 0 ° to 60 ° left. Maximum performance in the smallest of spaces

            - Miter cuts up to 60 ° left possible
            - Saw band length: 3650x27x0.9
            - single stroke: 600 mm (programmable up to 10m)
            - Simple 7 "touchscreen operation NC 5.0.
            - Saw arm made of spheroidal cast iron - robust and stable
            - Required space 3.4 m²
            - Footprint 1900mm wide x 1800mm deep

            With the new Shark 331 NC 5.0 Spider, MEP proves the high
            Performance requirement and maximum ease of use have a compact design
            can without foregoing all the components that ensure the safety of the
            Ensure operating personnel.

            Innovative (Windows CE based) 7 "touch screen control for easy and
            quick setting of all machine parameters and with additional software
            Keys for common functions

            Controlled head descent with automatic compensation via one in the cylinder
            mounted servo valve through constant monitoring of the torque and with
            precise setting in millimeters / minute
          Datasheet
          Request / Contact

          Section Shear - Combined

          used  Section Shear - Combined PEDDINGHAUS Peddiworker 500


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09166F · Section Shear - Combined

          PEDDINGHAUS - Peddiworker 500 - - 1991 -

          Technical details
          round bar steel 32 mm︱square edge steel 30 mm︱L-beam 80 x 8 mm︱hole punhing press: pressure 50 t︱hole punching press: throat 155 mm︱hole punching press: max. length of stroke 10 - 28 mm︱hole punching press: capacity (dia. x thick.) Ø27 in 14 mm︱work height max. 1024 mm︱shear: flat material 190 x 10 mm︱shear: length of knifes 200 mm︱Working height 705 mm︱adjustment of stroke 10 - 28 mm︱oil volume 40 l︱total power requirement 4 kW︱weight of the machine ca. 0,84 t︱dimensions of the machine ca. 0,65 x 1,2 x 1,67 m︱
          Hydraulic Section Shear - Combined
            round bar steel 32 mm
            square edge steel 30 mm
            L-beam 80 x 8 mm
            hole punhing press: pressure 50 t
            hole punching press: throat 155 mm
            hole punching press: max. length. 10 - 28 mm
            hole punching press: capacity (d. Ø27 in 14 mm
            work height max. 1024 mm
            shear: flat material 190 x 10 mm
            shear: length of knifes 200 mm
            Working height 705 mm
            adjustment of stroke 10 - 28 mm
            oil volume 40 l
            total power requirement 4 kW
            weight of the machine ca. 0,84 t
            dimensions of the machine ca. 0,65 x 1,2 x 1,67 m
            Description :
            Hydraulic Section Shear - Combined
          Datasheet
          Request / Contact
          used  Section Shear - Combined PEDDINGHAUS Peddimaster 60/100 H


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09165F · Section Shear - Combined

          PEDDINGHAUS - Peddimaster 60/100 H - - 1986 -

          Technical details
          round bar steel - mm︱square edge steel - mm︱L-beam 120 x 13 mm︱hole punhing press: pressure 60 t︱hole punching press: throat 510 mm︱hole punching press: capacity (dia. x thick.) Ø 27 in 17 mm︱shear: flat material 500 x 14 mm︱shear: flat material 400 x 16 mm︱shear: flat material 180 x 20 mm︱shear: flat material 120 x 21 mm︱shear: flat material 100 x 22 mm︱total power requirement 7,5 kW︱weight of the machine ca. 2,5 t︱dimensions of the machine ca. 1,8 x 0,9 x 1,8 m︱
          Hydraulic Section Shear - Combined
            round bar steel - mm
            square edge steel - mm
            L-beam 120 x 13 mm
            hole punhing press: pressure 60 t
            hole punching press: throat 510 mm
            hole punching press: capacity (d. Ø 27 in 17 mm
            shear: flat material 500 x 14 mm
            shear: flat material 400 x 16 mm
            shear: flat material 180 x 20 mm
            shear: flat material 120 x 21 mm
            shear: flat material 100 x 22 mm
            total power requirement 7,5 kW
            weight of the machine ca. 2,5 t
            dimensions of the machine ca. 1,8 x 0,9 x 1,8 m
            Description :
            Hydraulic Section Shear - Combined
          Datasheet
          Request / Contact

          Swarf Conveyor

          used  Swarf Conveyor MAYFRAN CleanSweep RM 125


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-196100 · Swarf Conveyor

          MAYFRAN - CleanSweep RM 125 - - 2021 -

          Technical details
          length in total 5108 mm︱band width 370 mm︱conveying height 1100 ︱length in width 880 mm︱weight of the machine ca. 0,7 t︱
          Suitable for Mazak Integrex i400S (T) x 1500 also for Integrex i200S / 300S x 1500
            length in total 5108 mm
            band width 370 mm
            conveying height 1100
            length in width 880 mm
            weight of the machine ca. 0,7 t
            Description :
            Suitable for Mazak Integrex i400S (T) x 1500
            also for Integrex i200S / 300S x 1500
          Datasheet
          Request / Contact
          •   
          •   
          • 1  
          •   
          •   

          Mager  &  Wedemeyer Werkzeugmaschinen GmbH  28309 Bremen Europaallee 24a Deutschland


          Contact Trader


            Mager & Wedemeyer Werkzeugmaschinen GmbH
           Europaallee 24a
            28309 Bremen
            Deutschland
            +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
            jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
            Contact person:

           




          Machine category


          Bandsägeautomat - Horizontal · Bearbeitungszentrum - Horizontal · Bearbeitungszentrum - Vertikal · CNC Drehmaschine · Leit- und Zugspindeldrehmaschine · Profilstahlschere - Kombiniert · Späneförderer ·