IproMac e.K. Willi Schneegaß - Stockist for used machines

turning diameter over bed 315 mm︱turning diameter over slide rest 630 mm︱turning length 1500 mm︱spindle bore diameter 81 mm︱total power requirement 5 kW︱weight of the machine ca. 3 t︱dimensions of the machine ca. 2,6 x 0,7 m︱

---

turning diameter 554 mm︱turning length 1000 mm︱control Fanuc ︱total power requirement 11 kW︱weight of the machine ca. 2,7 t︱dimensions of the machine ca. 2,6 x 1,6 x 1,8 m︱

---

HARRISON alpha 550 cycle lathe, used Controller: Fanuc Turning diameter: 554 mm Turning length: 1,000 mm Spindle passage: 90 mm Spindle: Speed (max.): 1,800 rpm Speed levels: 9 Power: 11kW Spindle passage (approx.): 90 mm Workpiece clamping: 3-jaw chuck, ø315 mm Tool carrier: Technology: quick-change holder on cross slide Travel in X: 310 mm Tailstock: Technology: Manual tailstock Quill ø: 95 mm Stroke: 145mm Taper: MK 6 Equipment/accessories: Chip management: chip tray Coolant management: KSS pump Shaft Machining: Fixed Bezel

turning diameter 555 mm︱turning length 1000 mm︱turning diameter over slide 290 mm︱3-jaw-chuck diameter 315 mm︱make Röhn ︱control Monforts MTCK︱quick change tool holder ohne- without steelholder ︱steady ︱turning speeds 2-2800 U/min︱transmission ratio 3 ︱face slide travel 235 mm︱spindle passage 70 mm︱tailstock quill taper MT 5 ︱total power requirement 15 kW︱weight of the machine ca. 3 t︱dimensions of the machine ca. 2,9 x 1,6 x 1,8 m︱

---

used machine MONFORTSKNC5-1000 Machine in good condition without Multifix steel holder

turning diameter 500 mm︱swing diameter 520 mm︱turning height mm︱Control Siemens 840 D ︱total power requirement 55 kW︱weight of the machine ca. 13,0 t︱dimensions of the machine ca. 3,95 X 1,57 x 3,20 m︱

---

Vertical lathe EMAG VSC 500 C-axis driven tools Control unit: Siemens 840D Workspace max. chuck diameter 500 mm Swing diameter 520 mm X-axis travel 1000 mm Z-axis travel 400 mm main spindle max. speed 3400 rpm Spindle bearing 160 mm main drive Maximum power 71 KW full power from 900 rpm maximum torque 750 Nm Holding torque continuous operation 480 Nm feed drive Rapid traverse X-axis 45 m/min Rapid traverse Z-axis 30 m/min Feed force in X + Z 11 KN disc revolver Recordings 12 DIN 69880 of which 12 are driven Shaft diameter 50 mm Electrical equipment 400 / 24 / 230 volts - 50 Hz Connected load 55 KW dimensions + weight L x W x H 3.95 x 1.57 x 3.2 m Weight 13500kg EQUIPMENT and ACCESSORIES 12x live tool turret 12x50 SW440, max. speed 6000 rpm, max torque 60 Nm direct path measuring systems in X + Z C-axis interpolation with X - and Z-axis, speed 0-100 rpm, Positioning accuracy 0.01 degrees open automation standard D=440 mm with workpiece diameter 500 mm, height 200 mm Chip conveyor hinged belt with brush discharge to the rear, discharge height 1250 mm Coolant device standard 80 liters at 8 bar / content 450 liters Extraction of mechanical filters Air volume 1000 cbm/h Lining diameter 500 mm Tools according to DIN 69880 Prepared for workpiece measurement Tools needed about 55 pcs fixed + powered tools

faceplate diameter 2000 mm︱swing diameter 2400 mm︱turning height 1800 mm︱ram adjustment 1200/1500 mm︱faceplate turning speed range -stepless- 2,3 - 250 U/min︱boring spindle drive 27 kW︱milling drive motor 27 kW︱spindle turning speed - stepless 0-1200 U/min︱tool magazin: 12 fach︱tool taper 50 ISO︱control Siemens 840 D sl ︱chip conveyor 2 ︱workpiece weight 15 t︱total power requirement 61/92 kW︱weight of the machine ca. 56 t︱dimensions of the machine ca. 10 x 10 x 7 m m︱

---

Machine type: CNC carousel lathe - double column Turning and milling center Turning - milling - drilling The machine was overhauled and modernized in 2014 automatic 12-fold tool changer C-axis driven tools • Tappet, hydrostatic bearing completely overhauled • Hyfraukik overhauled • Drives and ball screws renewed • Control conversion completely new to Siemens 840 D • New control cabinet • Complete housing with new automatic doors • New suction systems • New front guide covers • Both chip conveyors (wear-resistant) Knoll new • WW 12 places of which 2 horizontal - 1 vertical tool with SK holder interchangeable • Max. workpiece weight at medium-high speed 15 tons. Tool magazine: 12 compartments Accesories: Driven tools: 2 x horizontal 1 x Vertical Milling/drilling speed infinitely variable 0-1200 Various steel holders Various clamping claws Various milling cutters and drills 1 x face plate Ø 2000 mm 2 x faceplate Ø 2000 mm on pallet supports 1 x power chuck Ø 1200 mm 3 x pallets with various spare parts -complete Documentation/technical documents available -Foundation plan -Visit under power by appointment-

faceplate diameter 2000 mm︱swing diameter 2400 mm︱turning height 1800 mm︱faceplate turning speed range -stepless- 2,3 - 250 U/min︱ram adjustment 1200/1500 mm︱boring spindle drive 27 kW︱milling drive motor 27 kW︱spindle turning speed - stepless 0-1200 U/min︱tool magazin: 12 fach︱tool taper 50 ISO︱control Siemens 840 D sl ︱chip conveyor 2 ︱workpiece weight 15 t︱total power requirement 61/92 kW︱weight of the machine ca. 56 t︱dimensions of the machine ca. 10 x 10 x 7 m m︱

---

Machine type: CNC carousel lathe - double column Turning and milling center Turning - milling - drilling The machine was overhauled and modernized in 2014 automatic 12-fold tool changer C-axis driven tools • Tappet, hydrostatic bearing completely overhauled • Hyfraukik overhauled • Drives and ball screws renewed • Control conversion completely new to Siemens 840 D • New control cabinet • Complete housing with new automatic doors • New suction systems • New front guide covers • Both chip conveyors (wear-resistant) Knoll new • WW 12 places of which 2 horizontal - 1 vertical tool with SK holder interchangeable • Max. workpiece weight at medium-high speed 15 tons. Tool magazine: 12 compartments Accesories: Driven tools: 2 x horizontal 1 x Vertical Milling/drilling speed infinitely variable 0-1200 Various steel holders Various clamping claws Various milling cutters and drills 1 x face plate Ø 2000 mm 2 x faceplate Ø 2000 mm on pallet supports 1 x power chuck Ø 1200 mm 3 x pallets with various spare parts -complete Documentation/technical documents available -Foundation plan -Visit under power by appointment-

bore capacity in steel (diameter) 90 mm︱arm length 2500 mm︱workpiece height max. 1600 mm︱total power requirement 7,5 kW︱weight of the machine ca. 9,5 t︱dimensions of the machine ca. 3,6 x 1,6 x 3,6 m︱

---

Drilling capacity in steel (diameter): 90 mm Outreach: 2500 mm Workpiece height - max.: 1600 mm Tool holder: 6 MK Machine weight approx.: 9.5 t Space requirement approx.: 3.6 x 1.55 x 3.6 m

x-travel 3700 mm︱y-travel 840 mm︱z-travel 850 mm︱Tool bore SK 40 ︱tool magazin: 50 fach︱Control Siemens Sinumerik 840D ︱coolant 1 ︱total power requirement kW︱weight of the machine ca. 20 t︱dimensions of the machine ca. 8 x 3,5 x 3,5 m︱

---

CNC Machining Center - Vertical Manufacturer: CINCINNATI Type: FTV 840/3700 Year of construction: 2006 Serial No.: 7080-S00-KD0211 CNC control SIEMENS Sinumerik 840D SK40 tool holder tool changer T-slot clamping table approx. 3700x840 mm chip conveyor coolant treatment Accesories: approx. 180 tool holders SK40 (some with tools)

x-axis 2000 mm︱y-axis 1500 mm︱z-axis 750 mm︱burner heads 1 3 D︱laser capacity in Watt 2700 ︱

---

3D laser cutting and welding system TruLaser Cell 7020 Machine no. A0421A0099 Type: L13 standard equipment - X = 2000, Z = 750mm; B = +/- 135°; C = n x 360° - Laser TruFlow 2700 - Position laser diode - Stationary, rotatable pendant control panel - Teach panel - Teach software - Magnetic clutch, head detection - Laser power control - Power Cycles - Logbook function - focus line - Nitrogen jet aeration - Network connection including installation via teleservice - Analog modem for teleservice - Lighting boom - Documentation twice Deviating from this standard equipment or in addition the machine TruLaser Cell 7020 is equipped with: With the following configuration: Frequency 50Hz Voltage 400 V0 Electrical regulation IEC Language operating instructions German Number of operating instructions 2 pc Color standard RAL9002/5010 TruFlow 2700 Laser cutting (including preparation for laser welding) Incl. 2 cutting gases (02, N2), APC distance control, p Programmable cutting gas selection, adjustment device, Analog value cutting, pressure setting, valves Additional cutting gas argon Cutting optics f = 155 mm incl. sensor Stationary table 2000x1500 mm Second cutting optics (240 mm) Work table suction system including piping Compact deduster with 2000 Nm3/h including spark pre-separator, extraction pipe connection, for 1 active extraction point Protective cabin including separate extraction Special cover of the cabin top / roof Automatic sliding door in front Control panel including multi-button, acknowledgment and emergency stop Documentation twice / German The machine is delivered without additional Programming software, post processor and operator course. Annual service by Trumpf Service with proof Operating hours / as of 02/2022 Machine hours: 40,600h Laser on: 39,200h Beam on: 6,900h Last laser power measurement = 2790 watts (Optional) On request, we can also take care of the construction and commissioning through our laser service including training of your staff and a guarantee of 12 months (price on request)

x-travel 730 mm︱y-travel 730 mm︱z-travel 880 mm︱control 840 D sl Siemens︱size of pallet 500 X 500 mm︱total power requirement 46,2 kW︱weight of the machine ca. 15 t︱dimensions of the machine ca. 5,5 X 3,0 X 2,8 m︱

---

CNC machining center horizontal DMG MORI-NHX 5000 - 2-fold pallet changer - 15.094h spindle hours Technical details / accessories / supplement: x-travel 730 mm y-travel 730 mm z-travel 880 mm Control 840 D sl Siemens main spindle: max. spindle speed 12,000 rpm Drive power - milling spindle 30 kW Max torque 102Nm Tool holder SK 40 Distance spindle center to table 80 - 810 mm Distance spindle nose and table center 70 - 950 mm Pallet changer: Number of pallets 2 Pallet size 500 x 500 mm max. workpiece weight 500 kg max. workpiece diameter 800 mm max. workpiece height 1,100 mm Pallet change time 9.5 seconds Indexing time 1.3 sec B axis (table) 360 x 1° tool changer: Number of tool places 40 pos. Tool holder SK 40 maximum tool diameter 110 mm max. tool dia. with a free neighboring box. 320mm maximum tool length 550 mm max. tool weight 30.0 kg Changing time tool - tool 1.95 sec Changeover time Span - Span 4.4 - 10.0 sec feeds: Rapid traverse 60 m/min Feed speed max. 60,000 mm/min Inching feed speed 0 - 5,000 mm/min Total power requirement 46.2 kVA Machine weight approx. 15.0 t Space requirement approx. 5.5 x 3.0 x 2.8 m documentation chip conveyor coolant device High pressure cooling 40 bar internal coolant supply tool changer B axis 1° pallet changer Accessories (optional) Probe Renishaw PP 60 opt. approx. 70 recordings SK 40 (partly with tools)

x-travel 760 mm︱y-travel 460 mm︱z-travel 460 mm︱c-axis 360° ︱Control Okuma -OSP-E100M-H ︱drive motor 22/18,5 kW︱surface area Ø400 mm︱spindle turning speed range 50 - 12000 U/min︱tool taper BT 40 ︱weight of the machine ca. 7,5 t︱dimensions of the machine ca. 3,6 x 3,5 x 3,2 m︱

---

"Universal machining center OKUMA partially overhauled" new spindle and new clamping table Universal machining center 5 axes simultaneously Year of construction 2005. Manufacturer: OKUMA Type: MU 400VA Control: OSP-E100M-H TECHNICAL DATA Travel paths X-axis: 760mm Y axis: 460mm Z axis: 460mm C axis: 360° A-axis: +20 to -110° Table: Ø400 Spindle speed 50-12000 rpm Work recording: BT 40 / SK 40 Tool magazine: 32 compartments Tool changing system: Renolin type D10VG32 Hydraulic unit OMF1000 Coolant preparation/filter system Cooling through the spindle (IKZ) electronic handwheel chip conveyor High pressure cooling Weight 7260 kg Dimensions (LxWxH) in cm approx.: 3600 x 3500 x 3200

feed pressure 30 bar︱liter capacity 2900 / min l︱total power requirement 7,5 kW︱

---

voltage 230 V︱current 16 A︱output 3 kw︱working pressure 6 bar︱Number of boilers 1 ︱Steam production 5 kg/h︱Boiler temperature 165 °C︱Temperature at the nozzle (Steam) 120 °C︱Temperature at the nozzle (Steam+Water/Detergent) 90 °C︱Water tank capacity 5 l︱Detergent tank capacity 5 l︱water consumption 3,5 l/h︱Maximum length of hose 4 m︱Setting at work 4 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 500 mm︱width 450 mm︱height 850 mm︱weight 28 kg︱

---

Dry steam cleaner with suction Mach. No. 3449/19 TECHNICAL SPECIFICATIONS DRY VACUUM CLEANER - 3 circuit system steam steam and water + detergent Suction with blowing function - Voltage 220V 50Hz - Power 3000 watts - Steam production 5 kg/h - temperature 165°C in the boiler, up to 120°C at the nozzle outlet - Steam pressure 6 bar - Water tank 1 x 5 l (enough for approx. 1.5 hours) - Detergent tank 1 x 5 l - Mobile - Connection cable 5 m long - Case stainless steel - Dimensions L 500 x W 450 x H 850 mm - Weight 28kg - Ready to use in 4 minutes incl. accessories NEW PRICE EURO 2950,-

voltage 400 V︱current 63 A︱output 36 kw︱Production at 30924 kcal/h︱working pressure 10 bar︱Number of boilers 4 ︱Steam production 60 kg/h︱Boiler temperature 188 °C︱Temperature at the nozzle (Steam) 150 °C︱Temperature at the nozzle (Steam+Water/Detergent) 100 °C︱Water tank capacity 2 X50 l︱Detergent tank capacity 10 l︱water consumption 60 l/h︱Maximum length of hose 2 X 8 m︱Setting at work 5 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 1055 mm︱width 700 mm︱height 815 mm︱

---

Electronic steam generator and cleaning system Mach. No. 64002/12/16 - Electronically controlled - 3 circuit system steam steam and detergent steam and water - Voltage 400V/3-phase - Connection cable 5-pin, 8m long - Power 36,000 watts / 63 A - Steam production 60 kg/h - Steam pressure max. 12 bar - Temperature 188°C in the boiler up to 150°C at the nozzle outlet - Temperature steam-water mixture up to 100° - Water storage tank 2x50 liters - Detergent dosing and regulation - Hour meter - mobile / 2 wheels lockable - Hangers for hose and connection cable - 2nd working connections Accesories: 1 hose package with handle control (IP70/01 10m Reinforced Program) 1 long lance 1 lance short 1 brush holder 40 cm with round brush Completely workshop tested and repaired - Test according to BGV-A3 - Test run 1 hour

voltage 400 V︱current 32 A︱output 18 kw︱Production at 15462 kcal/h︱working pressure 10 bar︱Number of boilers 2 ︱Steam production 30 kg/h︱Boiler temperature 179 °C︱Temperature at the nozzle (Steam) 150 °C︱Temperature at the nozzle (Steam+Water/Detergent) 100 °C︱Water tank capacity 110 l︱Detergent tank capacity 2 x 1,4 l︱water consumption 30 l/h︱Maximum length of hose 8 m︱Setting at work 5 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 1055 mm︱width 700 mm︱height 815 mm︱

---

Electronic steam generator and cleaning system Masch. No. 90106/05 - Electronically controlled - 3 circuit system steam steam and water Steam and water cleaning agents - Voltage 400V/3-phase - Connection cable 5-pin, 8m long - Auto polarity switch - Power 18,000 watts - Temperature 180°C in the boiler up to 120-150°C at the nozzle outlet - Temperature of steam-water mixture up to 100° C - Steam pressure max. 10 bar - Storage tank 1 x 110 l - Detergent concentrate containers 2 x 1.4 l - Additive dosing system - Connection for vacuum cleaner 400 V / 3-phase - mobile / 2 wheels lockable - Hangers for hose and connection cable - Housing powder-coated RAL 5015 - Dimensions L1055 x W700 x H815 - Weight 165 kg Accesories: Hose package 4m analogue (IP10/03) Lance long 78 cm Completely workshop tested and repaired - Test according to BGV-A3 - Test run 1 hour

voltage 400 V︱current 32 A︱output 18 kw︱Production at 15462 kcal/h︱working pressure 10 bar︱Number of boilers 2 ︱Steam production 30 kg/h︱Boiler temperature 179 °C︱Temperature at the nozzle (Steam) 150 °C︱Temperature at the nozzle (Steam+Water/Detergent) 100 °C︱Water tank capacity 110 l︱Detergent tank capacity 1,4 l︱water consumption 30 l/h︱Maximum length of hose 8 m︱Setting at work 5 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 1610 mm︱width 470 mm︱height 1300 mm︱

---

Stationary steam generator and cleaning system Mach. No. 1300016/03 - Electronically controlled - 1 workstation connection - 2 circuit system steam steam and detergent - Voltage 400V/3-phase - Auto polarity switch - Power 18 KW - Heat output 15,462 kcal/h - Working pressure max. 10 bar - Number of steam generators 2 - Stainless steel boiler - Steam output 30 kg/h - Temperature 188°C in the boiler - Temperature at the nozzle outlet (steam) 120-150° C - Water consumption 30 l/h (at 100% utilization) - Temperature at the nozzle outlet (steam + cleaning agent) 100° C - Main steam valve - Electropneumatic - 5 l detergent concentrate container - Operating hours display230 - Case stainless steel - Dimensions approx. 1610 x 470 x 1300 mm - Weight 230 kg completely workshop tested and overhauled.

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

Steam production 120 kg/h︱working pressure 10 bis 12 bar︱ 72 KW kw︱Number of boilers 8 ︱weight 450 kg︱Dimensions (L/W/H) 2000 X 800 x 1800 mm︱

---

Discription: Industrial steam generator GIOVE 72 KW Quick steam generators Stationary - Electronically controlled - 1-circuit system steam - Voltage 400 V / 3-phase - Power 72 KW - thermal output 61 848 kcal / h - Working pressure max. 12 bar - Number of steam generators 8 - Steam output 120 kg / h - Temperature 188 ° C in the boiler - Temperature at the nozzle outlet (steam) 150 ° C - 1 access to supplies of external customers - Water consumption 120 l / h at 100% load - Feedwater submission / submission tank in Giove - Boiler drain system Ventury / semiautomatic - Interface / Control (potential free contacts) - Housing stainless steel dimensions: Length: 2 m x Width: 0.8 m x Height: 1.8 m Weight: 450kg Compl. Rebuilt in 2021 Manufacturer Approved Dez.2022 / Warranty: 3 Months