ATMH Werkzeugmaschinenhandel GmbH - Stockist for used machines

turning length 3000 mm︱centre height 300 mm︱turning diameter 600 mm︱total power requirement ca. 13 kW︱

---

turning diameter 700 mm︱turning length 300 mm︱spindle passage 80 mm︱turning dia. over face-slide 440 mm︱dimensions of the machine ca. 5,0x1,3x1,4 m︱

---

turning diameter over bed 1120 mm︱turning diameter over slide rest 800 mm︱turning length 3000 mm︱

---

turning length 1500 mm︱swing diameter over bed slide 310 mm︱spindle passage 80 mm︱turning speeds 22 - 1120 U/min︱Height of centres 295 mm︱turning diameter 590 mm︱required space 3,8 x 1,7 x 1,85 m︱

---

dimension Length: 3800mm Width: 1700mm Height: 1850mm Forkardt F400 chuck Three-jaw chuck diameter: 400mm

greates pass round over bed 1320 mm︱Swing over support 950 mm︱centre distance 11000 mm︱bed width 1100 mm︱bed height 560 mm︱total power requirement 65 kW︱weight of the machine ca. / t︱required space m︱

---

turning diameter over bed 655 mm︱turning diameter over slide rest 390 mm︱turning length 8150 mm︱peak load 6 t︱total power requirement 18,5 kW︱

---

accesories Bezels: 2 x ø40-215mm, 2 x ø100-380mm dimension Length: about 10200mm Width: about 1800mm Height: about 1800mm

turning length 1500 mm︱greates pass round over bed 600 mm︱swing diameter over slide rest 392 mm︱turning speeds 1435 U/min︱spindle bore 60 mm︱total power requirement 7,5 kW︱weight of the machine ca. 3,3 t︱required space m︱

---

turning diameter 620 mm︱turning length 1500 mm︱control Fanuc ︱bore diameter 80 mm︱

---

turning diameter 420 mm︱turning length 1200 mm︱control Fanuc ︱bore diameter 60 mm︱

---

centre height 345 mm︱turning diameter 690 mm︱turning length 2000 mm︱control Heidenhain Manual Plus ︱swing diameter over face slide 420 mm︱greates pass round over bed 710/760 mm︱longitudinal stroke 1970 ︱face stroke 385 ︱spindle bore 92 mm︱total power requirement 49 kW︱weight of the machine ca. 5,6 t︱required space / m︱

---

Accessories: 2 x Lynette and chip trays

turning diameter over slide rest / mm︱centre distance 1500 mm︱copying travel longitudinal / mm︱

---

Center height over flat track: 255mm Center height above prism upper edge: 237mm Turning diameter over bed: 520mm Turning diameter over the short lower slide: 300mm Turning diameter over the continuous lower slide: 270mm Faceplate diameter: 500mm Main spindle rotation 18 over wheels: 9 - 450 rpm Main spindle rotation 12 via belt: 140 - 1800 rpm Power requirement: 7.5 - 15kW Feeds Longitudinal normal: 0.33 - 2.0 mm / rev Longitudinal fine: 0.007 - 0.03 mm / rev Plan normal: 0.012 - 0.9 mm / rev Plan fine: 0.003 - 0.011 mm / rev Bed width: 403mm Spindle bore: 62mm

faceplate diameter 1000 mm︱turning diameter over slide rest / mm︱turning length / mm︱turning speeds 400 U/min︱total power requirement / kW︱weight of the machine ca. / t︱required space / m︱

---

turning length / mm︱turning diameter over plate // mm︱faceplate diameter / mm︱

---

Faceplate diameter: 3500mm Center height over plate: 1320mm Turning diameter over plate: 2600mm Turning diameter in the pit: 3600mm Turning diameter over bed: 1300mm Turning length: about 2400mm Max. workpiece weight: 22000kg Max. torque on the faceplate: 5000 mkg Faceplate ring gear pitch circle diameter: 1900mm Main spindle bore: 120mm range of speeds normal: 0.71-35.5 rpm increased: 1-50 rpm increased: 1.4-71 rpm Drive power: 38kW

Intern No: M14101486 ︱turning diameter over slide rest 2600 mm︱turning length 11000 mm︱turning diameter over bed 3300 mm︱weight of the machine ca. 120 t︱

---

Waldrich Siegen WDS 3000x11000 Max turning diameter: 3300 mm Max turning diameter over slide: 2600 mm Max turning length: 11000 mm Number of bed slide: 2 Outer diameter faceplate: 3000 mm Speed ??range: 0.67-55 rpm Workpiece weight between the tops: 45-50 t when using steady rest: 60-70 t Weight: 120 t Equipment: Grinding unit, dust extraction, 3 pieces steady rests On both sliders 4-axis digital display from Heidenhain. Price without tail stock Freight loading on truck A tailstock can be reproduced by us, price on request.

turning diameter 1200 mm︱turning length 3000 mm︱Control MTC S25 ︱turning diameter over bed ca. 1350 mm︱turning diameter over slide ca. 900 mm︱faceplate diameter 1200 mm︱center height of top slides 450 mm︱

---

Turning diameter over bed: approx. 1350mm Turning diameter over support: approx. 900mm Distance between centers: 3000mm Center height over support: 450mm Slideway width: approx. 700mm Faceplate diameter: 1200mm Lynette diameter: approx. 750mm

turning diameter 1500 mm︱turning length 1500 mm︱control Fagor 8055 T ︱turning diameter over bed slide 1250 mm︱total power requirement 45 kW︱weight of the machine ca. 12 t︱dimensions of the machine ca. 4 x 2,4 x 2x4 m︱

---

faceplate diameter 3200 mm︱swing diameter 3500 mm︱turning height 2200 mm︱range L-W-H 7730 x 6240 x 6700 mm︱control Typ 840 D sl ︱voltage 3 x 400 V︱frequency 50 Hz︱turning speeds 0,8 - 40 U/min︱max. turning diameter 3500 mm︱total power requirement 51 kW︱weight of the machine ca. 86 t︱

---

Technical specifications Machine type: CNC vertical lathe Manufacturer: Rafamet Year of manufacture: 1973 conventional General overhaul with control retrofit 2010 Control upgrade 2016 Control: Siemens 840 D Sl Condition: very good faceplate Turning diameter of the faceplate 3,200 mm Number of rotation stages of the face plate 3 (infinitely variable) Speed ??ranges of the faceplate 0.8 - 40 rpm Level I 0.8 – 3 rpm Level II 0.8 - 11 rpm Level III 0.8 – 40 rpm processing of workpieces Max. turning diameter 3,500 mm Max. turning height of the workpieces above the faceplate 2,200 mm vertical supports Smallest axis distance between the vertical supports 470 mm Largest ram travel of the left vertical support 985 mm Largest ram travel of the right vertical support 985 mm Axis Feeds - Infinitely variable feed Max.: X1.2 3m/min max.: z1.2 2.5 m/min Plunger cannot be pivoted Support — crossbar Rapid feed of the cross beam 600 mm/min Larger distance of the cross beam to the faceplate 2,300 mm load sizes +Permissible turning force when turning workpieces with a turning diameter of 2,000 mm and a turning speed of 20 m/min. 8,000kg +Largest chip cross-section for workpieces made of steel Fz = 50 kg/mm² at a turning speed of 20 m/min for all supports 45 mm² +Largest chip cross-section for workpieces made of steel Fz = 50 kg/mm² at a rotation speed of 20 m/min for a vertical support with max. plunger length 985 mm 2.5 mm² +Largest chip cross-section for cast iron workpieces HB = 160 kg/mm² at a turning speed of 20 m/min for all supports 120 mm² +Largest chip cross-section for cast iron workpieces HB = 160 kg/mm² at a rotation speed of 20 m/min for a vertical support with max. plunger length 985 mm 22.5 mm² +Largest permitted workpiece weight at 0.8 - 3.15 rpm 17,500 kg +Largest permitted workpiece weight at 4 - 40 rpm 7,500 kg electric motors Main drive motor power and revolutions 51 kW Power of the feed motors of: - Vertical support beam (2 pieces) 16 Nm (gear 1:10) - Tappet (2 pieces) 16 Nm (gear 1:12) Power and revolutions of the drive motor of the hydraulic pumps (2 pieces) 3kW - 1,500 rpm Power and revolutions of the clamp hydraulic motor of the vertical support beam 1.5 kW - 1,500 rpm Power and rotation for crossbar adjustment 15 kW - 1500 rpm 3.5 Information on the compressed air supply and other consumables Compressed air connection: 6 bar free of oil and water 3.6 Energy Consumption Conditions Voltage: 3 x 400V Control Voltage: 24V Frequency: 50Hz Fusing: 315 A Main dimensions and weight of the machine Length 7,730mm Width 6,240mm Height: 6,700mm Weight: 85,750 kg Tool: Capto 60 recording Not powered front panel Turning diameter of the front plate 3,200 mm Clamping disc diameter 3,400 mm Number of rotation levels of the front panel 3 (continuously adjustable) Front panel speed ranges 0.8 - 40 rpm Level I 0.8 - 3 rpm Level II 0.8 - 11 rpm Level III 0.8 - 40 rpm processing of workpieces Max. turning diameter 3,500 mm Max. turning height of the workpieces above the front panel 2,200 mm Vertical supports Smallest center distance between the vertical supports 470 mm Largest glide path of the left vertical support 985 mm Maximum glide path of the right vertical support 985 mm Axis feed - stepless feed max.: X1.2 3m/min max.: z1.2 2.5 m / min Support - mirror Fast feeding of the crossbeam 600 mm/min Greater distance between the crossbar and the front panel 2,300 mm loading sizes • Permissible torque when turning workpieces with a Turning diameter of 2,000 mm and turning speed from 20 m / min. 8,000 kg • Largest chip cross-section for workpieces made of steel Fz = 50 kg / mm2 at a speed of 20 m / min for all supports 45 mm2 • Largest chip cross-section for workpieces made of steel Fz = 50 kg / mm2 at a speed of 20 m / min for a vertical support at max. piston length 985 mm 2.5 mm2 • Largest chip cross section for workpieces made of cast iron HB = 160 kg / mm2 at a speed of 20 m / min for all supports 120 mm2 • Largest chip cross section for workpieces made of cast iron HB = 160 kg / mm2 at a speed of 20 m / min for a vertical support with max. piston length 985 mm 22.5 mm2 • Largest permissible workpiece weight at 0.8 - 3.15 rpm 17,500 kg • Largest permissible workpiece weight at 4 - 40 rpm 7,500 kg electric motors Main drive motor power and revolutions 51 kW Power of the feed motors of: - Vertical support rod (2 pieces) 16 Nm (gear 1:10) - Tappet (2 pieces) 16 Nm (gear 1:12) Power and revolutions of the drive motor of hydraulic pumps (2 pieces) 3 kW - 1,500 rpm Power and revolutions of the clamp hydraulic motor of the vertical support rod 1.5 kW - 1,500 rpm Power and rotation to adjust the crossbar 15 kW - 1500 rpm Information on compressed air supply and other consumables Compressed air connection: 6 bar free of oil and water Energy consumption, conditions Voltage: 3 x 400V Control Voltage: 24V Frequency: 50Hz Protection: 315 A noise and waste emissions Noise level under load 80.4 dB (A) Sinumerik control: Type 840 D sl Main dimensions and weight of the machine Length 7,730mm Width 6,240mm Height: 6,700mm Weight: 85,750 kg Weight clamp disc: 7,500 kg

faceplate diameter / mm︱swing diameter / mm︱turning height / mm︱

---

Year of construction: 1980, complete construction (mechanical and electrical) 1998 Control: Siemens Sinumerik 840T X: Face plate Ø 2400mm / max. Ø 2920mm / remove cover Ø 3010mm Z: 900mm W-slide travel: 900mm Accuracy: +/- 0.1mm Drive power: 60kW Additional equipment: Max. Workpiece height: 1820mm Max. Workpiece weight: 20 t Tool change / locations: NO Particularities: For pre-turning work, no coolant devices Type: turning Machine condition: According to age, is operated in 1 shift

bore capacity in steel (diameter) / mm︱throat / mm︱bore stroke 70 mm︱total power requirement 0,9 kW︱

---

Solid drill diameter 200 mm︱bore depth / mm︱number of spindles / ︱

---

Technical specifications Power: 129kW Control: Siemens NC control Speed ??range (stepless): 2 - 300 rpm Feed range (in steps): 3 - 4500 mm / min Oil system capacity: 20,000 liters Maximum flow rate: 1500 l / min Circumferential diameter in bezel: 1100mm Circumferential diameter over bed: 1250mm Distance between centers: 11000mm Clamping diameter faceplate: up to 1100mm Max. Workpiece weight with a stick: 10t Clamping range of the two steady rests: 150 - 1100mm Clamping range BOZA: 1 = 200 - 400mm 2 = 400 - 800mm dimension Min. Outside diameter: 406 mm Max. Outside diameter: 850mm Wall thickness: 10 .... 150mm Max. Workpiece length: 11000mm Max. Workpiece weight: 10 t Max. Strength: 800 N / mm² Specific cutting resistance (Ks): 2000 .... 2100 N / mm² Machine data Machine length: 28,800mm Center height: 560mm Circumferential diameter over bed: 1120mm Full drilling diameter: 200mm Core drill diameter: 350mm Boring diameter without drilling: 350mm Boring diameter with tapping: 350mm Headstock: Main drive motor: Siemens Type: 1 PH 7228 Performance data at 1,000 rpm: 113 kW / 1,079 Nm Performance data at 1,150 rpm: 129 kW / 1,017 Nm Main transmission: Z-F manual transmission Type: 2 K210 Switchable gear ratios: i = 1: 1 i = 1: 4 Fixed gear stage headstock: i = 11.68 Max. Torque: 50,000 Nm Speed ??range I: 2 ... 300 min Speed ??range II: 2 ... 75 min

spindle diameter 32-220 / 220 - 600 mm︱Control Siemens 840D ︱table load max. 1200 kg︱total power requirement / kW︱weight of the machine ca. 11 t︱required space 3,0 x 3,7 x 2,5 m︱

---

bore capacity in steel (diameter) / mm︱throat / mm︱bore stroke / mm︱total power requirement 1,1 kW︱weight of the machine ca. / t︱required space / m︱

---

bore capacity in steel (diameter) / mm︱arm length / mm︱workpiece height max. / mm︱

---

CLAMPING AREA Horizontal: 360x500mm Vertical: 400x500mm Groove width: 14H12mm Groove distance: 100mm Power: 1.5kW Spindle speed: 1600 min-1 Number of spindle power feeds: 3 Greatest feed force: 5000 Column diameter: 180mm Weight: 1250kg dimension Length: 1760mm Width: 915mm Height: 1970mm

spindle diameter 100 mm︱x-travel 1200 mm︱y-travel 1100 mm︱z-travel 1000 mm︱total power requirement / kW︱weight of the machine ca. / t︱required space / m︱

---