Kemmerich Werkzeugmaschinen GmbH - Stockist for used machines
Machinelist:
Cut-to-length-lines
- Kemmerich Werkzeugmaschinen
- Im Rottfeld 1a
- 40789 Monheim am Rhein
- Deutschland
-
+49 2173 207474
+49 2173 207473 -
info@kemmerich.biz
www.kemmerich.biz
#1020-19439 · Cut-to-length-lines
HITACHI - - - 1993 -
Technical details
Stainless steel Cut to Length Line(Flying type) - Material: stainless steel, surface treated steel -- Thickness: 0.3–3 mm (as of stainless steel) -- Width: 500-1350 mm -- Trim: 5-25 mm on one side (more than twice the plate thickness) - Material coil: internal diameter 508 mm, external diameter 600–1800 mm -- weight maximum 15 tons -- Width accuracy: 500–1350 mm plus or minus 0.2 mm (when side trimming) -- Product length: 400–6000 mm Plus/minus 0.3 mm - 6-leveler (6-hi) leveler x 2units types -- Tension: 45 to 50 kg/mm2 -- Yield point: 28 kg/mm2 - Cutting method: Cut while running (flying), numerically controlled rocking type - flying shears -- (Cutting speed) 20–40/80 m/min -- Speed 2-speed change type --- 0.3 to 1.2 mm: 20 to 80 m/min --- 0.21–3 mm: 20–40 m/min -- Slow operation: 0.8 m/min -- Conveyor speed: 20~120m/min -- Cut count: up to 150 cuts/min -- (Product piling) --- Plate width: 500–1350 mm --- No1 piler: 400 to 3100 mm (also used as a reject filer) --- No2 piler: 400–6100 mm --- Load height: up to 600mm --- Load weight: up to 4 tons Line direction: From right to left on control panel Line: Approximately 13 m x 49.050 m (Major facilities) - Coil skid - Coil car - Pay off reel and a paper winder - Coil opener - Rough Leveler - Shear - No. 1 Looper Guide - Side guide and pinch roller - Side trimmer - Scrap winder x2 - No.1 Finisher Leveler (6-hi) - No2 Finisher Leveler (6-hi) - No 2 Looper Guide - Measuring roller, feed roller and paper-off reel - Shear - Conveyor - Cart - No1/No2 piler type - Hydraulic unit: Type - Valve stand type - (Coil skid) -- V-type fixed skid -- Coil maintenance: 1 coil -- Coil weight: up to 15 tonnes -- Coil diameter: 600 to 1800 mm -urethane rubber (Coil Car) Cradle roller type Hydraulic boost Electricity transfer driving type Two guide lots hydraulic cylinder elevating type (payoff reel and paper winder) Overhang, single-mant 4-segment type Paper reel motor: DC 5.5KW 400/1600 RPM, attached to brake Paper winder: cone type, (motor DC 1.5KW, 1750 RPM) (Coil Opener) Knife edge method (Rough Leveler) 2-stage (2hi) 5-body roller leveler Pinch rollers: 160 mm × 1450 mm 2 pieces, The upper part of the pinch roller is hydraulic cylinder press-down, and the lower roller is fixed 5 workload rollers 130mm x 1450mm The upper roller of the workload roller is electrically pressed, and the lower roller is fixed 0–40/80 m/min Two-stage change 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Motor: DC 18.5 KW, 1750 RPM, Brake Attachment Pressing motor: 2 1.5KW 100RPMs with brakes (Shear) Hydraulic up cut shear Knife size: 25 mm thickness × 150 mm width × 1450 mm length (No. 1 Looper Guide) Table lift Hydraulic cylinder operation method Loop: Light Volume Control Method Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Side guide and pinch roller) Vertical Free Roller Electrically switched type Side guide roller: 90 mm diameter × 150 mm length × 6 bones Pinch Roller: 2nd Stage (2hi) Roller: 160 mm diameter × 1450 mm length × 2 bones Upper roller: pneumatic cylinder pressure free roller Lower Roller: Fixed Drive Roller (Side trimmer) Overhang Drive Cut 0–40/80 m/min 2-stage change type 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Cutter diameter: 320 mm / 190 mm internal diameter × 20 mm thickness Roller: 320 mm external diameter × 19 mm internal diameter × 20 mm thickness Motor: DC 5.5KW 1750RPM (Scrap winder) Two machines Link Pin Gauge Type (Hydraulic Cylinder Opening and Closing Type) Motor: 2 DC 2.2KW 1450 RPM (No1 Finisher Leveler) 6-level (6-hi) 17 leveler Thickness: 1.21–3.0 mm Speed: 6 to 40/80 m/min Thickness 0.3–1.2 mm 6–80 m/min Thickness 1.21–3 mm 6–40 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 60mm x 1750mm x 17e 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium roller: 50 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 88 mm Diameter x 50 mm Length x 7 rows Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 55KW 1750 RPM Brake Attachment (No2 Finisher Leveler) 6-level (6-hi) 17 leveler Plate thickness: 0.3–1.2 mm Speed: 5 to 80 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 35mm x 1750mm x 17bon 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium Roller: 32 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 99 mm Diameter x 50 mm Length x 7 rows Roller bearing type Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 35KW 1750RPM Brake Attachment (No. 2 Looper Guide) Table lift Hydraulic cylinder operation method Loop: How to control the amount of light (amount of light) Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Measuring roll/feed roller/paper vinyl payoff reel) Measuring roller: The upper roll is pneumatic pressing, the lower roll is fixed, the pressing amount is 30 mm Feed roller: Upper roll is pneumatic cylinder press, lower roll is fixed, press load is 40 mm Motor: DC 2.2KW 1750RPM (Shear) Fluctuating Flying shear 0.3~3mm Speed: 2 groups of 20–40/80 m/min Thickness 0.3–1.6 mm 80 m/min Tlate thickness 1.6–3 mm 40 m/min Cut count: up to 150 cuts/min Cutting length: 400–6000 mm Electric up CUT shear Cut up and down knife die via motor, reducer, pinion stand crankshaft Knife: 20 mmt × 80 mm × 1400 mm × 1 set The top knife is a straight knife, and the bottom is a V-lock knife Adjustment: Wedge Motor: DC 75KW 550RPM (Conveyor) Belt conveyor type Belt width: 1200 mm Conveyor length: 3800 mm Motor DC 5.5KW 1450RPM Brake Attachment (No. 1 No. 2 piler) No1 piler: Combined use of reject truck, air blower Combined use of side conveyor No2 piler: Combined suction conveyor and air blower Loading height: 600 mm Lift: Hydraulic lift volume 650 mm Motor: 4 1.5KW 150RPM units for side guide end stoppers 2.2 KW 1500RPM for lifters 1.5KW for cart 7.5KW for blower (Hydraulic device) 70 kg/cm2 × 100 L/min Pen pump Motor: DC 18.5 KW 1000 RPM (Supply power) AC400 V,50 Hertz 3 Phase / AC200 V,50 Hertz 3 Phase (Control power) AC 200V, 50 Hz Single Phase (Compressed air) Compressed air required: 5 kg/cm2
Trader Profile: Kemmerich Werkzeugmaschinen
GmbH
Contact Trader
GmbH
Im Rottfeld 1a
40789 - Monheim am Rhein
Deutschland
+49 2173 207474">+49 2173 207474
+49 2173 207473
info@kemmerich.biz
www.kemmerich.biz
Profile of Trader
| ||||||||||||
|
Mr. Volker Kemmerich | Mr. Andreas Kemmerich |
Phone: 02173 / 207472 | Phone: 02173 / 207474 |
Fax: 02173 / 207473 | Fax: 02173 / 207473 |
E-Mail: sales@kemmerich.biz | E-Mail: info@kemmerich.biz |
Im Rottfeld 1a
Contact Trader
Im Rottfeld 1a
40789 - Monheim am Rhein
Deutschland
+49 2173 207474
+49 2173 207473
info@kemmerich.biz
www.kemmerich.biz
Contact person:
Herrn Andreas Kemmerich +49 2173 207474
Seit 1982 ist die Firma Kemmerich Werkzeugmaschinen GmbH auf dem sich ständig ändernden Werkzeugmaschinen-Markt aktiv und handelt als international tätiges Maschinen-Handelsunternehmen mit gebrauchten Maschinen für die spanabhebende und spanlose Verarbeitung der metallverarbeitenden Industrie
Kemmerich ist dabei auf Zahnradbearbeitungsmaschinen und Maschinen der Schwerzerspanung, wie zum Beispiel Dreh-, Fräs- und Schleifmaschinen sowie Bohrwerke, spezialisiert. Die Maschinen kommen unter anderem in der Automobilindustrie (Ausrüster und Zulieferer), im Zahnrad- und Getriebebau, der Produktion von Kugel- oder Wälzlagern, dem allgemeinen Maschinenbau zum Einsatz.
Ansässig ist das Unternehmen inzwischen in Monheim am Rhein, im Herzen des Rheinlandes und in unmittelbarer Nähe zu den Messestädten Köln und Düsseldorf und deren Flughäfen. Dort stehen auf einer 2.200 qm großen, beheizbaren Ausstellungsfläche eine Vielzahl von konventionellen wie auch CNC/SPS-gesteuerten Metall be- und verarbeitenden Werkzeugmaschinen stets zur Besichtigung und Vorführung bereit.
Mit einer Krankapazität von 32 Tonnen können jegliche Art von Maschinen gehändelt und bewegt werden. In der eigenen Werkstatt werden die Funktionsfähigkeit der Maschinen überprüft und gegebenenfalls festgestellte Mängel beseitigt. Zudem werden Maschinen auf Kundenwunsch modernisiert und modifiziert. Das Leistungsspektrum des Unternehmens umfasst zudem die Demontage oder Demontageüberwachung, Verladung, Verpackung sowie Land-, Seetransport und Zollabwicklungen, Montage und Inbetriebnahme beim Kunden durch Vermittlung von Spezialisten, Präsentation der Maschinen unter Strom (soweit möglich), Durchführung von Maschinenbewertungen und die Vermittlung von Kontakten.
Anstatt in neue, teure Werkzeugmaschinen zu investieren und um lange Lieferzeiten zu umgehen, lohnt es sich oftmals, eine gut gepflegte Gebrauchtmaschine zu kaufen.