x-travel 2500 mm︱y-travel 3000 mm︱z-travel 1250 mm︱Control HEIDENHAIN iTNC530 ︱spindle turning speed range 22000 U/min︱tool change unit 50 -fach︱tool taper HSK 63 A ︱rated capacity kVA︱milling-head swivable +/- 110° ︱c-axis +-300° ︱total power requirement 130 kW︱weight of the machine ca. 60 t︱dimensions of the machine ca. 7,6 x 7,3 x 5,7 m︱

---

This ZIMMERMANN FZ33c is in a very good condition as new. The machine can be viewed under power by arrangement only until week 15. be inspected. Description: Technical data of the machine and working ranges X-axis 2500 mm Y-axis 3000 mm Z-axis 1250 mm A-axis ± 110 ° C-axis ± 300 ° incl. vibration sensor incl. bearing temperature sensor incl. rotary feed-through for inner KM-feed IKZ 5-axis path control: Heidenhain iTNC 530/handwheel HR520, 15" TFT colour display Extraction system Keller Vario P1 Machine room roofing Tool changer 50-fold, chain magazine, behind the machine Chip conveyor, ejection 60° left, front side Renishaw RMP60 measuring probe Blum laser tool measurement "Control NT-Micro Clamping table Length x width x height 2500 x 3250 x 400mm Table load 8000 kg/m² (max. 16000 kg) T-slots, arranged lengthwise 18H12 Distance between T-slots 250 mm Dimensions, weights Space requirement (without peripherals) approx. 7600 x 7300 x 5650 mm Total weight approx. 53500 kg Electrical connection Voltage (three-phase) 400 V Frequency 50 Hz Fuse see installation plan Power requirement see installation plan Compressed air connection (on-site) Required air pressure 6 bar Average air consumption approx. 15 m³/h (depending on machine equipment) Linear axis drives Feed speed X-, Y-, Z-axis 60 m/min Axis acceleration X-, Y-, Z-axis up to 5 m/s² Drives rotary axes -VH30 Feed speed A-, C-axis 360 °/s Axis acceleration A-, C-axis 700 °/s² Resolution A-, C-axis 0.0001 Accuracies of linear axes - according to VDI / DGQ 3441 Positioning accuracy X-axis P= 0.026 mm Y-axis P= 0,028 mm Z-axis P= 0,020 mm Repeat accuracy X-axis Ps= 0.015 mm Y-axis Ps= 0,016 mm Z-axis Ps= 0,010 mm Resolution of the measuring systems (interpol) A-, C- axis 0,0001°. Accuracy rotary axes -VH30 Positioning accuracy A-, C- axis P= 12" = 0,0033°. Repeat accuracy A-, C- axis Ps= 8" = 0,0022°. Milling head VH30 2-axis milling head: VH30, Milling spindle Siemens Weiss Spindle power S1 (100% ED) 60kW, spindle speed 22.000 min-1, 95Nm, HSK-A63 Outer dimensions fork head L x W approx. 500 x 600 mm Nominal torque rotary axes control loop A: min. 1200 Nm C: min. 1047 Nm clamped A- and C-axis: 3000 Nm (permanent grease lubrication with automatic relubrication system) Swivel axis - spindle nose 326 mm Tool holder HSK 63 A Tool clamping Spring clamp Tool clamping Hydraulic Permissible tool weight 4.5 kg (manufacturer's specification) Coolant supply outside and inside Coolant-lubricant supply (emulsion) at the front of the milling spindle with belt filter system Volume 1500 l Pump 1: 40l/min at 20 bar Pump 2: 20l/min at 40 bar, Blowing air at the front of the milling spindle

x-travel 6800 mm︱y-travel 3400 mm︱z-travel 2000 mm︱Control HH iTNC 530 ︱table dimension - longitudinal 6000 mm︱table dimension - cross 2500 mm︱table load 10 t︱tool change unit 80 Pos.︱dist. between columns - front to rear 4700 mm︱total power requirement kW︱weight of the machine ca. 80 t︱dimensions of the machine ca. 12 x 11 x 7 m︱

---

This portal milling machine is in good condition and can be inspected by arrangement be inspected under power at the seller's premises. Description: - 80-position tool changer with 40 positions ISO SK-50 / 40 positions HSK-63A - 4-fold automatic head changer - 2 pieces orthogonal milling head OAD with: --> Tool holder ISO SK-50 --> Spindle speed: 20-6000 rpm --> 46kW drive power (100% ED S1) - 1 piece 2-axis fork milling head E5E (CAC II) with: --> HSK-63A tool holder --> swivelling range C-axis: +/- 200° --> swivelling range B-axis: +/- 100° --> drive power 37kW --> Spindle speed max. 24000 rpm, ***** Spindle DEFECTIVE !!! ***** 1 vertical spindle F-400 --> Spindle speed 4000 rpm --> drive power 25kW IKZ 38bar with paper belt filter 2 chip conveyors (lengthwise channelling belt conveyor 1 cross conveyor Heidenhain longitudinal measuring rods in all three axes Z-axis with 4-fold linear guide Wireless measuring probe M&H 20.41 Multi BRANKAM machine protection system CMS-100 (collision protection) Working area cover (roof) can be opened at the rear and front BLUM tool measurement Heidenhain HR 550 FS radio handwheel X and Y-axis drive via rack and 2 pinions Z-axis drive via ball screw

x-travel 6000 mm︱y-travel 3500 mm︱z-travel 1500 mm︱Control SIEMENS 840D ︱table load 12 t︱height over floor 6300 mm︱table dimension - longitudinal 5000 mm︱table dimension - cross 2500 mm︱no. of tables 2 ︱tool change unit 200 -fach︱weight of tools max. 30 kg︱tool taper HSK A 100 ︱diameter of tools max. 250 mm︱workpiece length 500 mm︱spindle turning speed range 5-6000 U/min︱c-axis -10 bis 370 °︱b-axis 5 bis -95 °︱column daylight 3000 mm︱distance spindle nose and table 1500 mm︱total power requirement kW︱

---

x-travel 14000 mm︱y-travel 5000 mm︱z-travel 1500 mm︱w-axis 3000 mm︱column daylight 4000 mm︱column: max. dist. table - spindle nose 4500 mm︱workpiece weight 100 t︱table dimension - longitudinal 9000 mm︱table dimension - cross 3000 mm︱spindle taper ISO SK 50 ︱spindle turning speed range 2-2500 U/min︱spindle motor 113 kW︱spindle diameter 200 mm︱max. torque on the spindle 9500 Nm︱feed in x - axis 1-10000 mm/min︱feed in y - axis 1-10000 mm/min︱feed range Z-direction 1-10000 mm/min︱rapid traverse 20000 mm/min︱height over floor 8600 mm︱control SIEMENS 840C ︱

---

ATTACHMENTS angular milling head yes autom. tool clamping yes ball spindles yes guideway covers yes coolant unit yes high pressure cooling syst. (through spindle) yes closed cabin yes chip conveyor yes TECHNICAL DESCRIPTION PLANER TYPE MACHINING CENTER - EACH WITH 3 PALLETS 9000 x 3000 mm: - Tool changer with 420 tools - Head pick-up system - Video monitoring via camera - High pressure lubrication unit for inner cooling 70bar AVAILABLE HEAD UNITS: - Fixed angle head HS800C600 105 Kw 600 long - Fixed angle head HSD350C850 50 Kw 850 long - Fixed angle head HSD 40C880 12 Kw 880 long - Fixed angle head HSD 190C1000 30 Kw 1000 long - Vertical spindle unit VS800C 105 Kw 900 long - Universal spindle unit USIO40C 20 Kw B-axis rotatable at 1° at a time - Angle spindle unit SO800C905 - 22,5° fix - Angle spindle unit HSE1200CS -25° fix - Universal spindle unit (fork milling) USP475C 75 Kw 1/2° Hirth One additional drilling extension SE 350C plus 1 SE500C. DESCRIPTION OF CONDITION In 2011/2012 these 2 identical machines were retrofitted The milling length was extended to 14meters and an automatic changing system for table pallets was installed. Both machines can be seen under power by prior appointment.

x-travel 4000 mm︱y-travel 2500 mm︱z-travel 1200 mm︱Control FIDIA M30 ︱spindle 37 kW︱turning speeds 4500 U/min︱column daylight 2300 mm︱dist. milling spindle - table surface 1250 mm︱taper ISO SK-50 ︱table dimension - longitudinal 3000 mm︱table dimension - cross 1500 mm︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱

---

x-travel 6200 mm︱y-travel 3200 mm︱z-travel 1000 mm︱Control HEIDENHAIN iTNC 530 ︱number of spindle speeds 2000 U/min.︱table dimension - longitudinal 3500 mm︱table dimension - cross 2000 mm︱table load 20 t︱T-slot - distance 125 mm︱T-slot - width 28 mm︱tool taper SK-50 ︱tool change unit 300 -fach︱column daylight 2350 mm︱coolant IKZ 60 bar︱w-axis 1500 mm︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. 12700 x 11000 x 6000 m︱

---