Single Column Press - Hydraulic

pressure 200 t︱throat - mm︱stroke 250 mm︱Table dimensions 2420 x 840 mm︱ram surface 1850 x 650 mm︱dayligth 500 mm︱ram adjustment 110 mm︱distance between columns 1900 mm︱table height 170 mm︱no. of strokes 25 - 45 Hub/min︱total power requirement 22 kW︱dimensions of the machine ca. 2550 x 2370 x 3820 mm︱weight 30 t︱

---

- pneumatic clutch - press safety valve, Herion - cam switch, Balluff - chain break monitoring - hydr. overload, Hydac - motor. alide adjustment with digital display - separate control cabinet with safety control ABB - separate two-hand control panel with foot switch - slidable side protective doors - front protection by light barriers vertical + horizontal The machine shown and described above is safe for hand inlays. The machine is also in anorther variant or also can be used as an automatic feeder. Equipment possible according to customer agreement.

pressure 3500 kN︱distance between columns . mm︱stroke 400 mm︱strokes - infinitely variable 15-25 Hub/min︱ram surface 2050 x 1150 x 885 mm︱table surface area 2120 x 1220 mm︱Motor Capacity 45 kW︱total power requirement kW︱weight of the machine ca. 70 t︱dimensions of the machine ca. 3120 x 2450 x 7000 m︱

---

rebuild in 2017

press capacity 50 KN︱strokes - infinitely variable max. 100 Hub/min︱table-size 550 x 500 mm︱distance between columns 370 x 320 mm︱height of stroke 30 mm︱Control Touch ︱air pressure - required 6 bar︱voltage 380 V︱weight of the machine ca. 1,2 t︱dimensions of the machine ca. 2,55 x 1,00 x 2,10 (2,6) m︱

---

Built-in tool 220 x 230 mm height 75 mm + 60 mm

pressure 160 t︱distance between columns 2700 mm︱stroke 280 mm︱ram adjustment 120 mm︱daylight (stroke down, ram adjustment above) 550 mm︱table surface area 2700 x 1200 mm︱ram surface 2700 x 1200 mm︱no. of strokes 20 - 40 Hub/min︱total power requirement 22 kW︱weight of the machine ca. 33 t︱dimensions of the machine ca. B 3,52 x T 2,85 x H 4,55 m︱

---

Double-column eccentric press in a special design - size of the GTX 250 S, but only a pressing force of 160 t Furnishing: - hydraulic roller bars - hydraulic Tool clamping above + below - Motorized ram adjustment - infinitely variable speed control - hydraulic overload - Grease central lubrication - Hand oiler for ram weight compensation converted by MAWI GmbH Germany: - Swivel arm with Siemens Touch control panel - Light barrier from Sick - Safety control from Pilz + Siemens - frequency converter - Monitored protection area at the rear

pressure 160 t︱distance between columns 2700 mm︱stroke 280 mm︱ram adjustment 120 mm︱daylight (stroke down, ram adjustment above) 550 mm︱table surface area 2700 x 1200 mm︱ram surface 2700 x 1200 mm︱no. of strokes 20 - 40 Hub/min︱total power requirement 22 kW︱weight of the machine ca. 33 t︱dimensions of the machine ca. B 3,52 x T 2,85 x H 4,55 m︱

---

Double-column eccentric press in a special design - size of the GTX 250 S, but only a pressing force of 160 t Furnishing: - hydraulic roller bars - hydraulic Tool clamping above + below - Motorized ram adjustment - infinitely variable speed control - hydraulic overload - Grease central lubrication - Hand oiler for ram weight compensation converted by MAWI GmbH Germany: - Swivel arm with Siemens Touch control panel - Light barrier from Sick - Safety control from Pilz + Siemens - frequency converter - Monitored protection area at the rear

pressure 63 t︱distance between columns 320 mm︱stroke 8 - 120 mm︱table-size 800 x 600 mm︱ram surface 500 x 400 mm︱throat 315 mm︱dayligth 410 mm︱ram adjustment 70 mm︱no. of strokes 56 / 90 Hub/min︱total power requirement 6 kW︱weight of the machine ca. 5,5 t︱dimensions 2,10 x 1,52 x 2,72 m︱

---

inclinable

pressure 160 t︱dayligth 700 mm︱number of strokes adjustable 30 - 180 min︱table-size 1600 x 640 mm︱distance between columns 1600 mm︱ram surface 1440 x 950 mm︱hole in the table 1300 x 350 mm︱ram adjustment 100 mm︱daylight between the side columns 640 x 700 mm︱stroke of ram - solid 40 mm︱total power requirement 30 kW︱weight of the machine ca. 25 t︱dimensions of the machine ca. ca. 3 x 2,3 x 4 m︱

---

- With hydraulic overload - With shuttle table device

Pressure total 315 t︱Slide adjustment 125 mm︱Shut height (stroke down, adjustment up) 700 mm︱Free frontal opening L-R 2450 mm︱Table surface area 2200 x 1300 mm︱Hole in table 1200 x 600 mm︱Ejector in ram 60 t︱Ejector stroke in ram 10 mm︱Number of strokes 15 - 150 min-1︱Main Motor 61 kW︱Height over floor approx. 5500 mm︱

---

pressure 350 t︱stroke 101,6 mm︱ram - range of adjustment ca. 100 mm︱table-size 1750 x 920 mm︱column travel -side 630 x 380 mm︱no. of strokes 46 Hub/min︱total power requirement 35 kW︱weight of the machine ca. 41 t︱dimensions of the machine ca. 4 x 2,7 x 4,8 m︱

---

pressure 40 t︱distance between columns 450 mm︱stroke 20-50 mm︱ram - range of adjustment 60 mm︱table surface area 370x400 mm︱ram surface 250x370 mm︱hole in the table 120x280 mm︱table height 850 mm︱weight of the machine ca. 2,5 t︱dimensions of the machine ca. BxTxH 1600x1300x2800 mm︱

---

pressure 500 t︱distance between columns 1600 mm︱stroke 60 mm︱max. ram stroke 60 1 / min︱ram adjustment 100 mm︱dayligth 700 mm︱Table area 1600x1400 mm︱ram surface 1400x1150 mm︱total power requirement kW︱weight of the machine ca. 40 t︱dimensions of the machine ca. m︱

---

About usmore than 400 machines in the warehouse over 12000 m² storage area, crane capacity 70 tmore than 1000 items accessories for your workshopYou want to sell machines production lines or your company, then talk to us.

neu ︱ ca. 10 Wochen ab Auftrags ︱ Türkei ︱ 400 to︱ 2200 mm︱ 1200 mm︱ 340 mm︱ 200 mm︱ 20 - 30 1/min︱ 1100x1100 mm︱ 55 kW︱ 2170 mm︱ 5100 mm︱ 5850 mm︱ 51000 kg︱

---

8-fold ram guide light guard motorized ram adjustment hydraulic overload safety device motorized lubrication according to CE rules user manual in GERMAN and ENGLISH

neu ︱ ca. 10 Wochen ab Auftrags ︱ Türkei ︱ 200 to︱ 1600 mm︱ 1000 mm︱ 250 mm︱ 60 mm︱ 35 - 70 1/min︱ 900x700 mm︱ 100 mm︱ 22 kW︱ 2100 mm︱ 3900 mm︱ 5144 mm︱ 20000 kg︱

---

8-fold ram guide light guard motorized ram adjustment hydraulic overload safety device motorized lubrication according to CE rules user manual in GERMAN and ENGLISH

neu ︱ ca. 10 Wochen ab Auftrags ︱ Türkei ︱ 300 to︱ 1800 mm︱ 1200 mm︱ 355 mm︱ 180 mm︱ 26 1/min︱ 1460x1090 mm︱ 140 mm︱ 45 kW︱ 2600 mm︱ 4400 mm︱ 5240 mm︱ 48000 kg︱

---

8-fold ram guide light guard motorized ram adjustment hydraulic overload safety device motorized lubrication according to CE rules user manual in GERMAN and ENGLISH

pressure 2 t︱throat 150 mm︱stroke 150 mm︱distance table/ram, max. stroke up, adjustment up mm︱table surface area 310 x 250 mm︱hole in the table mm︱table height over floor mm︱power requirement 2,0 kW︱weight of the machine ca. 0,6 t︱dimensions of the machine ca. 1,2 x 0,8 x 1,7 m︱

---

Single column press - with table base - various press accessories

pressure 28 t︱throat 225 mm︱stroke 150 mm︱table surface area 325 x 300 mm︱work speed 2 - 9,8 mm/sek︱return speed 12,8 mm/sek︱total power requirement 4 kW︱weight of the machine ca. 650 kg︱dimensions of the machine ca. 1800 x 900 x 2000 mm︱

---

- NC control to adjust the piston stroke - Selector switch for manual or semi-automatic operation - Flow control valve and pressure control valve - Integrated pressure gauge - Various tools can be installed on the piston - inside There is a 40 mm hole for attaching the tools

pressure 160 t︱throat 350 mm︱stroke 140 mm︱dayligth 370 mm︱table surface area 750 x 620 mm︱hole in the table 220 mm︱table height over floor 850 mm︱ram surface 750 x 580 mm︱oil volume 700 l︱feed down 300 mm/sec︱feed up 480 mm/sec︱feed under pressure 58 mm/sec︱total power requirement 60 kW︱weight of the machine ca. 10,8 t︱required space 2,4 x 1,8 x 3,5 m︱

---

permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, controllable two-hand operation 2020: new electrical (safety) control - Siemens S7-1500 F, easy operation via touch-panel Design of the electrical control according to DIN EN ISO 16092-1/-2/-3 year of manufacture 1995

pressure 25 t︱throat 300 mm︱stroke 400 mm︱Number of working hours 1235 h︱table-size 650 x 500 mm︱ram surface 550 x 450 mm︱dayligth 700 mm︱rapid traverse - down 500 mm/sec︱work speed 27 - 72 mm/sec︱rapid traverse - up 410 mm/sec︱quantity of oil 230 l︱die cushion capacity 125 kN︱die cushion stroke 200 mm︱capacity of ejector 8 kN︱ejector stroke 150 mm︱total power requirement 7,5 kW︱weight of the machine ca. 3,3 t︱dimensions of the machine ca. 1,3 x 1,6 x 2,8 m︱Electric 400 Volt ︱Light barrier in front ︱

---

Little used (only 1235 hours!) hydraulic single column press, power 25 t with Pilz safety control, ejector, light barrier and 2-manual operation. Upgrade with a current Pilz safety controller Mod. PNOZMulti m2pin in 2017. There is a small one in the piston rod of the cylinder Ejector cylinder integrated, which is controlled single-acting. The return stroke of the ejector takes place without force due to thesubsequent stroke of the Press cylinder. Machine intended for optionally retrofittable die cushion. Machine free due to production change. It comes from a large company and has been constantly maintained and kept up to date. Machine dealer with own stock of 1600 m²

pressure 25 t︱stroke 150 mm︱throat 420 mm︱dayligth 450 mm︱table surface area 700 x 820 mm︱table height over floor 850 mm︱ram surface 600 x 600 mm︱feed down 370 mm/s︱feed up 370 mm/s︱working feed 18 - 33 mm/s︱oil volume 300 l︱power requirement 5,5 kW︱Weight 5,8 t︱dimensions of the machine ca. 1,1 x 2,0 x 2,4 mxmxm︱

---

permitted for manual loading according to the CE-norm with oil-hydraulic drive, controllable dependent on pressure/time and way, cutting impact cushioning, mechanical depth stop, two-hand operation

Pressing force 10 t︱oil pressure max. in the work cylinder 310 bar︱engine output 3 kW︱tracking travel 70 ms 8 mm︱weight 1650 kg︱

---

pressure 30 t︱throat max. 250 mm︱stroke max. 200 mm︱dayligth 475 mm︱table surface area 550 x 500 mm︱weight of the machine ca. 2050 kg︱power stroke 20 mm︱

---

pressure 40 t︱throat 300 mm︱stroke 630 mm︱dayligth 900 mm︱table surface area 620 x 520 mm︱hole in the table 150 mm︱table height over floor 600 mm︱ram surface 150 mm︱total power requirement 15,0 kW︱weight of the machine ca. 4,5 t︱required space 1,0 x 1,9 x 3,0 m︱

---

permitted for manual loading according to the CE Regulations with oil-hydraulic drive, controllable dependent on pressure/time and way, two-hand operation press can be inspected in running condition in our warehouse

pressure 40 t︱throat 330 mm︱stroke 250 mm︱dayligth 450 mm︱table surface area 800 x 500 mm︱hole in the table 100 mm︱table height over floor 900 mm︱ram surface 100 mm︱feed down 406 mm/sec︱feed up 393 mm/sec︱feed under pressure 14 mm/sec︱oil volume 350 l︱total power requirement 7,5 kW︱weight of the machine ca. 4,6 t︱required space 1,3 x 2,3 x 3,4 m︱

---

permitted for manual loading according to the CE Regulations with oil-hydraulic drive, controllable dependent on pressure/time and way, mechanical depth stop, two-hand operation press can be inspected in running condition in our warehouse

pressure 10 t︱throat 0 mm︱stroke 400 mm︱total power requirement 7,5 kW︱weight of the machine ca. 6500 t︱dimensions of the machine ca. m︱

---

D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weight, approx. 6,500 kg Accessories / Special Features * DUNKES CNC Control, Model 200, can be programmed with presettable parameters, e.g. Stroke, speed, forward and return motion, pressing time, etc. * Separate switch cabinet with floppy disk input. * Pendant control with monitor. * Two-handed release, in conjunction with pneumatic safety door. * A turning device for calibrating and smoothing of bores is mounted on the ram. (Calibrating mandrel moves into the bore and rotates, powered by it own motor-driven timer. Repetitions are controlled by stroke counter.)